Bộ lọc

Tìm kiếm gần đây của tôi
Lọc theo:
Ngân sách
đến
đến
đến
Loại
Nhiều kỹ năng
Ngôn ngữ
    Tình trạng công việc
    9 công việc được tìm thấy, giá theo USD

    I want to mesh a square cylinder enclosed in a rectangular domain. Dimensions are: side of square cylinder: 1 m upstream distance: 20 m downstream distance: 40 m height of domain 60 m I am enclosing a sample 2D mesh. The project is to create a 3D mesh so that I could do numerical simulations on it with dynamic meshing. Dynamic meshing setting will be done in the circular zone near the square cylinder.

    $74 (Avg Bid)
    $74 Giá đặt trung bình
    8 lượt đặt giá
    Meshing for simulations in ANSYS FLUENT 4 ngày left
    ĐÃ XÁC THỰC

    I want to mesh a square cylinder enclosed in a rectangular domain. Dimensions are: side of square cylinder: 1 m upstream distance: 20 m downstream distance: 40 m height of domain 60 m I am enclosing a sample 2D mesh. The project is to create a 3D mesh so that I could do numerical simulations on it with dynamic meshing. Dynamic meshing setting will be done in the circular zone near the square cylinder.

    $94 (Avg Bid)
    $94 Giá đặt trung bình
    5 lượt đặt giá

    I need to find traction and slip on a wheel

    $100 (Avg Bid)
    $100 Giá đặt trung bình
    13 lượt đặt giá

    I am working on Non-Isothermal PE-100 pipe extrusion. I am applying cross law for viscosity dependence on shear rate and Arrhenius law for viscosity dependence on temperature in direct extrusion at POLYFLOW. When i run, it shows solution is not converge. When I change the viscosity to be not temperature dependent, then the solution can be converged. So there is any way to make it converge and in the same time take the temperature into account to determine the viscosity? where I am wrong? I am struck here. Kindly help me.

    $14 (Avg Bid)
    $14 Giá đặt trung bình
    4 lượt đặt giá

    We've to perform CFD (Flow Simulation) of a Vertical Axis Wind Turbine.

    $20 (Avg Bid)
    $20 Giá đặt trung bình
    6 lượt đặt giá
    CFD expert 1 ngày left
    ĐÃ XÁC THỰC

    To do a task with report, contact me for more details

    $80 (Avg Bid)
    $80 Giá đặt trung bình
    31 lượt đặt giá

    i want to model and design coaxial pseudo magnetic gear with a gear ratio of g1-g2:6.45, g2-g3: 9.14 total gear ratio of 59.012987. the modeling will be first done using a Permanent magnet and then PPM-PM key parameters of interest are transferable torque limit, roto size, toque density, etc

    $145 (Avg Bid)
    $145 Giá đặt trung bình
    12 lượt đặt giá

    need to perform an acoustic analysis to reduce the noise in the aqua silencer to 80db

    $57 (Avg Bid)
    $57 Giá đặt trung bình
    9 lượt đặt giá

    In this project we need to reduce the noise from the silencer to 80db with changing design of silencer

    $89 (Avg Bid)
    $89 Giá đặt trung bình
    7 lượt đặt giá