Điện tử Jobs

My 4.5 V circuit needs a small solar panel and the proper charge-management hardware so daylight tops the battery up automatically. I’m not sure what panel voltage or wattage is best, nor which controller IC will keep the Li-ion safe—so I need your electronics expertise. Scope of work – I'll share my schematic of the existing 4.5v circuit – Select or design a charge-controller stage that handles lithium-ion chemistry, prevents over-charge/over-discharge, and outputs a stable 4.5 V rail to the load. – Provide a clear schematic, concise BOM with part numbers that are easy to source, and wiring instructions I can follow on perfboard or a small PCB. – Advise on any protection components (diodes, fuses, reverse-polarity safeguards) so the device...

My setup is an ESP32 wired to a 2.8-inch ILI9341 LCD (I may swap to the 3.2-inch variant; both share the same driver and pinout). All images sit on an SD card; more than fifty of them may be shown . I need a complete MicroPython solution that pulls each JPG straight from the card and pushes it to the display with no intermediate PC-side conversion. Core needs • Initialize the ILI9341 (ST7789) over SPI, handle 320×240 resolution, and work with both display sizes out of the box. • Mount the SD card, scan a folder, and stream-decode each JPG so the ESP32’s RAM footprint stays within limits. • Cycle through every file in the list inside an endless loop; I’ll decide the delay between frames in a simple variable (e.g., DELAY_MS). • Show each image f...

I need a clean, well-commented Arduino sketch for the Pololu 3pi that lets the robot visit six preset locations, interact with the magnet at each spot, and return to its starting line in under four minutes. The only sensing method available is a magnetic sensor array, so all point detection and interaction logic must rely on that hardware. Two run modes have to coexist in the same program and be switchable through a simple flag, jumper, or serial command: • Intermediate – the robot must physically touch the magnet before leaving the point. • Difficult – the robot should recognise the magnetic field, stop just short of contact, and then continue. Between locations, I expect a mix of straight dashes and graceful curves; please handle path planning so the 3pi&r...

I have five separate street-lighting circuits, each running roughly 1 km and powered by LED fixtures. For every run I must keep the voltage drop under 3 % . Your job is to size the conductors, select protective devices if required, and supply clear voltage-drop calculations that prove compliance for each feeder. Please base the work on standard RTA specs, and assume a three-phase, four-wire low-voltage supply 400V. Deliverables • Single-line or schematic for all five circuits showing conductor sizes and protection • Spreadsheet or calculation sheet detailing input data, formulas, and the final % drop for every circuit • Short narrative explaining any assumptions, cable grouping or ambient-temperature corrections applied I will review the numbers, confirm that no...

======================================= OVERVIEW ======================================= We need a complete design package for a standalone, battery-powered audio device. The device plays pre-recorded church bell audio files from a microSD card at three scheduled times per day (6 AM, 12 PM, 6 PM). Purely hardware-controlled — no app, no WiFi, no Bluetooth required for operation. We handle fabrication separately through JLCPCB. Your deliverables are design files only. ======================================= WHAT THE DEVICE DOES ======================================= * Plays a 2-3 minute audio recording at user-selected times (6 AM, 12 PM, and/or 6 PM) * 3 toggle switches to enable/disable each time independently * Rotary switch to select from 8-12 audio files stored on mi...

DESCRIPCIÓN: Busco estudiante o técnico de electrónica para realizar pruebas y validación de firmware en un proyecto real basado en ESP32. El firmware ya está desarrollado y estructurado. El trabajo consiste en: * Compilar firmware * Cargarlo en ESP32 * Realizar pruebas guiadas * Reportar resultados La arquitectura del sistema y el seguimiento técnico están organizados mediante asistencia de inteligencia artificial que ya conoce el proyecto completo y va indicando los pasos a ejecutar. El técnico no tiene que diseñar el sistema, solo ejecutar pruebas y reportar. QUE SE OFRECE: Este es un proyecto real que se está preparando para salir al mercado. Además de la remuneración, se ofrece: * Partic...

I need the 2026 GC front panel converted into a production-ready Gerber package so my board house can mill an exact aluminum faceplate. All mechanical data are already prepared: you’ll receive a clear photo of the current panel plus an Excel sheet detailing every cut-out, hole diameter, and positional coordinate. No circuitry is involved—this is purely a mechanical PCB. Here’s what I expect: • A clean RS-274X Gerber set, including drill file, that matches the spreadsheet dimensions to the tenth of a millimetre. • A simple PDF drawing or fabrication note that calls out all critical sizes for one last visual check before I release it to the shop. Please stick to the manufacturer’s standard rules; I’ll share their design-rule file once we start, ...

I need a medium complexity (3-4 layers) PCB designed for signal processing. The design should be capable of accommodating surface-mount components. Requirements: - 3-4 layers PCB design - Signal processing functionality - Surface-mount component integration - Gerber file generation Ideal Skills: - Experience with PCB design software (e.g., Altium, Eagle) - Strong understanding of signal processing circuits - Proficiency in layout for surface-mount components - Attention to detail and accuracy Please provide samples of previous work.

I'm looking for a device that can measure weight in pounds and operate underwater. It's essential that this device is powered by long-lasting batteries. Key Requirements: - The device must be waterproof and able to function accurately while submerged. - It should measure weight specifically in pounds. - Long-lasting battery life is crucial to ensure extended use without frequent recharging or replacement. Ideal Skills and Experience: - Experience in designing waterproof electronic devices. - Knowledge in weight measurement technology. - Expertise in battery technology for prolonged usage. Please provide examples of previous work and relevant experience in your bids.

I’d like the design published here turned into a finished, fully-working machine and delivered to me ready for use. The printable parts in the download need to be produced on a reliable FDM printer, finished cleanly, and paired with the necessary electronics. Key tasks you’ll handle • 3D-print every part from the MakerWorld files in a strong, heat-resistant material. Some parts need to be printer in PETG. • Source and install the electronics including arduino, wire everything neatly. • Run a full test roll, capture a short video showing the winder in action. • Ship the completed unit. Needs to work for Australian plug 240V. Total parts cost is estimated at US$170 ## Estimated Parts Cost **Electronics:** - Arduino Nano: ~$5–8 - DC Motor 1...

I’d like a playful, interactive cactus that mounts on a small vase and behaves almost like a tiny robot. When I trigger it with a micro:bit the body should sway side-to-side and then spin a full 180°. The stem must remain visibly “soft”, so please design it with flexible joints or a TPU sleeve while still leaving firm pockets for the hardware. Electronics I already have on hand • micro:bit + matching extension board • two micro servo motors for the wiggle and the rotation • an ultrasonic sensor for proximity detection • several RGB LED beads to make the pot glow Your model needs to include precise seats and cable channels for all of the above, plus screw-posts or clips so I can open the shell, swap parts and run wires without tearing an...

I have a finished KiCad PCB layout and now need a clean, print-ready PDF compiled from it. The final document must contain six A4 landscape pages arranged in this exact order: 1. Copper Top Layer 2. Copper Inner Layer 1 3. Copper Inner Layer 2 4. Copper Bottom Layer 5. Component Placement Top Layer 6. Component Placement Bottom Layer Resolution has to be crisp enough for both close-up review and high-quality printing. I’ll provide the KiCad source files as soon as we get started; you simply export each required layer, keep KiCad’s default rendering colours, and merge them into a single PDF. I’ve attached a previous example—please note the labels are mirrored on that file due to an earlier issue, so yours should read correctly. Deliverable • O...

Hello, I am looking for an experienced PCB designer to complete schematic review and PCB layout for an ESP32-based industrial IoT board using EasyEDA (Collaborator mode). Scope of Work 1. PCB Outline & Mechanical Alignment The PCB outline must match an existing device layout based on measurements and connector positions that I will provide. There is no reference Gerber file, so the board outline must be recreated carefully and confirmed with me before routing. 2. Schematic Review & Improvement (Important) You must review the schematic and confirm it is electrically correct and suitable for stable operation, including: Component ratings verification Power design validation Decoupling and grounding ESP32 stability considerations LM2596 switching regulator layout considerations Identi...

I'm seeking an experienced PCB designer to create a double-layer PCB for a consumer electronics radio project. The PCB will include microcontrollers as key components. Key Requirements: - Design a double-layer PCB - Incorporate microcontrollers into the design - Suitable for consumer electronics use Ideal Skills and Experience: - Proficiency in PCB design software (e.g., Altium, KiCad) - Experience with double-layer PCB design - Knowledge of microcontroller integration - Background in consumer electronics Please provide samples of previous work and relevant experience.

Description: We are developing a prototype of a motor control system based on an existing PCB that uses an ATmega16 microcontroller. The current system controls the speed and torque of the main motor and the speed of a secondary motor. Inputs are presently taken from a custom-made keyboard with tactile push buttons, and motor control is achieved by pulling specific GPIO pins high or low in defined sequences. The objective of this task is to replace the physical keyboard input system with a capacitive touch LCD display, where the on-screen UI buttons will perform the same functions as the existing tactile buttons. The touchscreen interface will control motor on/off, speed, and torque, while ensuring that the existing motor control logic based on GPIO sequences remains functionally the same....

I need an expert to tune a DSP (Digital Signal Processor) for a custom-built Bluetooth speaker aimed at delivering a balanced sound profile across all music genres. The speaker will be used primarily for music. Requirements: - Use of Sigma Studio for DSP tuning - Tailoring sound profile to specific speaker and box size - Experience with balanced sound profiles - Knowledge of various music genres The ideal candidate should have a strong background in audio engineering and experience with DSP software.

Vui lòng Đăng Ký hoặc Đăng Nhập để xem thông tin.

I need an existing wiring schematic revised to add one component. Requirements: - Current schematic is scanned from PDF - Need to add a green pilot light Ideal Skills: - Experience with wiring schematics - Proficient with PDF editing and schematic modification - Attention to detail and accuracy

Custom TWS Earbuds Prototype - Earin M-2 Miniaturization** UNIVERSITY PROJECT: Redesign Earin M-2 earbuds SMALLER to reduce ear protrusion. CURRENT SPECS: 24×15×15mm shell, 4g each, 60mAh battery, 4hr playback, BA driver, NFMI sync, touch controls TARGET SPECS: <20×13×12mm shell (33% smaller volume) • Same features or close equivalents • 1-2 FULLY WORKING prototype pairs DELIVERABLES REQUIRED: 1. New shell design (3D printed or molded) 2. Custom PCB layout for reduced volume 3. Component sourcing (mini BA driver, BT/NFMI, 40-50mAh battery) 4. Full assembly + functional testing 5. Audio test + TWS pairing validation I HAVE: • Complete Earin M-2 teardown photos • Exact measurements + target dimensions • Protrusion problem photos &bu...

I need a focused research effort that looks at satellite-communication antennas from three angles at once: maximising signal strength and quality, mapping frequency-band usage, and refining antenna design and materials. The outcome should give me clear, data-backed guidance I can hand straight to my hardware team. Scope You will survey current literature and patents, run electromagnetic simulations (HFSS, CST, FEKO or similar), and translate the findings into practical design recommendations. Emphasis is on L-, S- or Ku-band performance; however, if your analysis uncovers a better-suited band, flag it and justify the choice. Deliverables • Concise comparative report (PDF) • Simulation files with setup notes • Performance charts showing gain, VSWR, efficiency and li...

I’m kicking off a multi-phase R&D effort devoted to the design and development of cutting-edge microstrip antennas. The overarching targets are straightforward: boost usable bandwidth while simultaneously lifting signal strength, all without compromising the core advantages of printed technology. Phase by phase, I’ll be iterating from theoretical models through to lab-verified prototypes. You’ll take the lead on concept generation, electromagnetic simulation (HFSS, CST or an equivalent full-wave solver), layout refinement, and hand-over for fabrication. Once hardware comes back, we’ll compare measured S-parameters and radiation patterns against the simulated baseline, fine-tune, and document lessons learned for the next spin. Key deliverables • Simulation...

I am developing a compact handheld consumer device prototype that requires integration of a rechargeable battery and small electronic module inside a custom 3D printed enclosure. I am looking for an experienced embedded hardware / electronics engineer who can help design and prototype a small, safe, battery-powered system suitable for a handheld form factor. The device will require: • Integration of a rechargeable lithium battery (3.7V or similar) • Safe charging system (USB-C or similar) • Small heating or vapor-generating element OR similar compact load component • Efficient power management and protection circuitry • Compact PCB design suitable for fitting inside a slim enclosure • Guidance on component selection and prototype assembly The enclosur...

Projeto: Engenharia Reversa de Placa Eletrônica Legada Descrição do Projeto Busco profissional com experiência comprovada em eletrônica para realizar engenharia reversa completa de uma placa eletrônica legada, com o objetivo de: Reproduzir fielmente o funcionamento elétrico original Modernizar componentes obsoletos Gerar documentação técnica completa e atualizada Garantir compatibilidade mecânica, elétrica e funcional com o equipamento original O projeto seguirá um procedimento técnico estruturado já definido internamente Escopo do Trabalho O profissional deverá executar as seguintes etapas: 1. Análise e Correlação do Esquemático Verificaç&...

After successfully finalizing our first version of our automotive braking system board, we would now like to improve the design to make it modular, safe, reliable, and production ready. Requirements: Fixes: - Analyze and fix the power issue on the board. - Make minor labeling corrections and adjust components placement - Add a few more components based on provided requirements Create two board versions: 1. Improved board with all findings fixed. 2. Production board with a professional enclosure. - Reduce board cost by eliminating unnecessary components. - Consider EMC tests. - Select the best interface connector. - Enable board variants. Other requirements: - The chosen candidate must be open to schedule video or voice calls whenever necessary. - The chosen candidate is required to sig...

I new to design a PCB dedicated to processing several signals and starting a device based on a set number of conditions. I would like to be able to modify those parameters from a cloud based or simple web interface. The board should handles both analog and digital. I expect all to be digital signals but just in case. It should basically handle, temperature, humidity and time of day. Deliverables 1. Compiled firmware binaries plus full, buildable project files 2. Clear inline comments and a concise README explaining build steps and pin mappings 3. A short test report that documents signal-integrity measurements and confirms the module meets the agreed specs. 4, Plus device recommendation and also help on setting up. I have an idea, but I am a genetic engineer. I am OK with basi...

I already have the full schematic and the finished PCB files for a board that combines an ESP module with a PIC18F microcontroller. What I’m missing is a clear, practical explanation of how everything talks to each other, especially over UART, and how that interaction is implemented on the physical board. Here is what I need from you: • A step-by-step walkthrough of the signal paths that handle UART traffic between the ESP and the PIC18F, including any level-shifting, buffering, or hand-shake lines that support the link. • A guided tour of the PCB layout that shows where those signals travel—layer changes, vias, ground references, decoupling, and any routing choices that affect integrity or noise. • Simple notes on any supporting circuitry (power rails, ...

I've already built some prototypes of a circuit capable of switching a single 230 V, 16–30 A line to 4, 8, or 12 outputs—without power loss—but none of them have reached the standards I expect. I have schematics, calculations, thermal measurements, and test logs: enough material to clarify every technical detail and speed up your work. I need a senior designer who can transform all this into a final solution, complete with ESP32 firmware, a multilayer PCB (4 or 6 layers, JLCPCB production - 3oz copper), and an accurate and documented simulation before production. Technical requirements to be met: • Maximum energy efficiency, component protection, and precision switching under load. • Integrated remote control, real-time monitoring, and an alarm system. &b...

I already have the full schematic and the finished PCB files for a board that combines an ESP module with a PIC18F microcontroller. What I’m missing is a clear, practical explanation of how everything talks to each other, especially over UART, and how that interaction is implemented on the physical board. Here is what I need from you: • A step-by-step walkthrough of the signal paths that handle UART traffic between the ESP and the PIC18F, including any level-shifting, buffering, or hand-shake lines that support the link. • A guided tour of the PCB layout that shows where those signals travel—layer changes, vias, ground references, decoupling, and any routing choices that affect integrity or noise. • Simple notes on any supporting circuitry (power rails, ...

I need solution for three questions electronics MATLAB/simulations file attached 1.35 1.36 1.39 Only induvial experts and tutors no agencies After this i will have so many projects Fair price flexible with time good availability of time

Ho già costruito alcuni prototipi di un circuito in grado di commutare un’unica linea da 230 V, 16–30 A, verso 4, 8 o 12 uscite; --senza perdita di potenza--, nessuno, però, raggiunge ancora gli standard che mi aspetto. Dispongo di schemi, calcoli, misurazioni termiche e log di prova: materiale sufficiente per chiarire ogni dettaglio tecnico e velocizzare il tuo lavoro. Mi occorre un progettista senior che sappia trasformare tutto questo in una soluzione definitiva, completa di firmware su ESP32, con PCB multilayer (4 o 6 strati, produzione JLCPCB - copper 3once) e una simulazione accurata e documentata prima della produzione. Requisiti tecnici da rispettare • Massima efficienza energetica, protezione dei componenti e precisione nella commutazione sot...

I'm seeking an engineer to create an intelligent mouse trap focused on monitoring and alerting. The trap should utilize a motion sensor for mouse detection and an actuator to trigger a trap upon detection. Key Requirements: - Motion sensor for detection - Actuator to trigger trap - Notification system for alerts Ideal Skills and Experience: - Experience with sensors and actuators - Knowledge in IoT and notification systems - Background in hardware development and prototyping Please share your relevant experience and approach.

I’m replacing my existing pool circulation unit with a single-speed pump that I already have on site, along with all the fittings, unions, and electrical hardware required. The pad is clear, the plumbing is exposed, and access from the driveway to the equipment area is wide open, so getting tools and materials in place will be straightforward. What I need is a qualified installer who can: • Plumb the new pump into the current PVC line, ensuring airtight, leak-free unions • Make the electrical connection to the existing breaker, verify correct voltage, and bond/ground to code • Prime, test-run, and fine-tune the flow so the system reaches full pressure without cavitation • Leave the pad clean and walk me through basic operation once everything is running sm...

I’m building a smart irrigation setup that links a Raspberry Pi edge server with several ESP32 nodes in the field. Each ESP32 gathers data from soil-moisture probes, compact weather boards (temperature, humidity, barometric pressure), and inline flow meters, then reports everything wirelessly to the Pi for processing. Here’s what I need from you: • Python (Raspberry Pi) and MicroPython/C++ (ESP32) code that ingests the raw sensor streams, pushes them through an on-device model, and decides—within seconds—whether to start or stop the main pump and which solenoid valves to open. • An ML pipeline: training notebooks, a lightweight model (TensorFlow Lite or similar) and the inference wrapper that runs locally. The model must act on current soil-moisture rea...

I need a plastic enclosure designed for a screen-free WiFi kids phone. The design should be injection moulding ready and include internal layouts for PCB, speaker, and silicone rubber buttons. Requirements: - DFM (Design for Manufacturing) is essential. - Deliverables should include STEP files and production drawings. - Enclosure material: ABS - Finish: Matte - Buttons: Silicone rubber buttons Ideal Skills and Experience: - Experience in consumer electronics design - Proficient in creating DFM-ready designs - Strong knowledge of injection moulding processes - Expertise in producing detailed STEP files and production drawings Please share relevant portfolios with your bids.

I need a custom ELRS (ExpressLRS) solution for drone control, utilizing an STM microcontroller instead of the original MCU. Key requirements: - Improved range - Enhanced security - Dual band - Mesh networking capabilities Ideal skills and experience: - Proficiency in STM microcontrollers, especially STM32 - Strong background in RF communication and protocols - Experience with drone control systems - Knowledge of security implementations in wireless networks - Familiarity with mesh networking technology Please provide relevant experience in your bids.

I need an experienced electrician for industrial installation work. The task involves installing machinery and equipment in an industrial setting. Ideal Skills and Experience: - Experience in industrial electrical work - Expertise in machinery and equipment installation - Knowledge of safety regulations and compliance - Ability to read and interpret electrical blueprints and schematics - Problem-solving skills and attention to detail - Relevant certifications and licenses

I'm looking for an Arduino code that will trigger RGB LEDs to change color based on a pulse rotary dial input. Requirements: - Use of a pulse rotary dial - RGB LEDs whose colors will be controlled by the rotary dial input Ideal Skills and Experience: - Proficient in Arduino programming - Experience with rotary dials and RGB LED control - Familiarity with electronics and circuit design

Hello , I have a cabled weather station ready to go, but I need an experienced hand with the physical installation side only. The job covers everything from mounting the sensors and console, running and securing the cable, to making sure connections are weather-proofed, grounded, and reading correctly once powered up. Brand is flexible—I simply need someone familiar with the usual hardware found in systems such as Davis Instruments, AcuRite, La Crosse, or similar. Only serious freelancer Auto bids not good Thank you

I have a cabled weather station ready to go, but I need an experienced hand with the physical installation side only. The job covers everything from mounting the sensors and console, running and securing the cable, to making sure connections are weather-proofed, grounded, and reading correctly once powered up. Brand is flexible—I simply need someone familiar with the usual hardware found in systems such as Davis Instruments, AcuRite, La Crosse, or similar. Key Deliverables • Sensors, mast, and console solidly mounted in their designated locations • All cables routed neatly, protected from the elements, and correctly terminated • Grounding and surge protection in place where required • Final power-up and verification that the station is delivering clean, sta...

I'm seeking an experienced product designer to develop an ultrasonic scent diffuser. Key Features: - Timer settings - LED lighting - Mist intensity control Ideal Skills and Experience: - Proven experience in designing consumer electronics, particularly scent diffusers - Strong understanding of ultrasonic technology - Expertise in integrating LED lighting and timer mechanisms - Ability to create intuitive user interfaces Please include relevant experience in your application.

I’m developing a compact medical-grade board that will sit at the heart of a new vital-signs monitor. The PCB must reliably acquire and process heart rate, blood pressure, and respiratory rate signals, then pass the data to a microcontroller for further analysis and display. Here’s what I need from you: • Complete schematic capture based on my sensor and MCU selections • Four-layer board layout optimized for low-noise biomedical signals (Altium or KiCad preferred) • Manufacture-ready Gerber files, pick-and-place data, and a clearly structured BOM with medical-grade component choices • Design reviews at schematic and pre-release layout stages so we can make sure the board meets IEC 60601-1/-2 spacing, leakage, and isolation requirements • Brief ...

Vui lòng Đăng Ký hoặc Đăng Nhập để xem thông tin.

I am looking for someone to develop hardware on my request, it will be simple projects as seen on you tube. I am interested to know hourly rates, if I provide the hardware and code they would just need to wire them up. Would be nice to have someone from India NCR.

I need an expert to establish communication between two Siemens S7-1500 PLCs using OPC UA. Requirements: - Send digital, analog, and alarm signals. - Control a program on the server PLC via the client PLC. - Transmit maintenance data. Ideal skills and experience: - Experience with Siemens S7-1500 and OPC UA. - Proficiency in handling digital, analog, and alarm signals. - Strong background in PLC programming and communication protocols. Please provide relevant work experience in your bids.

I need a PCB designed specifically for a one-off project; it is not part of a commercial product line, so flexibility and creativity are welcome. The board will carry only analog circuitry—no digital sections—centred around operational amplifiers and a small signal-processing stage I will detail once we start. What I will supply: the schematic (PDF or KiCad), preferred footprints, and basic mechanical constraints. What I need from you: a clean, manufacturable layout with proper analog grounding practices, complete Gerber/ODB++ files, a reviewed BOM, and the original design file so I can revise it later if needed. Please aim for standard two-layer construction unless you advise otherwise for noise reasons. Acceptance will be based on: • DRC-clean files that import i...

The task is to design a compact PCB that drops straight into an SCX 1/32 car so it can run on a digital track. I want the board to read the track’s reed-sensor signal, let me assign any of 20 unique car IDs in firmware, and expose a surface-mount USB-C port on the edge for easy flashing once the body shell is back on. Size must stay close to the original analogue board footprint (about 24 × 18 mm, height under 6 mm) but I can adapt mounting holes or connector positions if you have a cleaner layout idea. Power comes from the standard track pickups (nominal 14–18 V DC), so include an efficient buck or LDO to feed the microcontroller and reed circuitry. I haven’t locked the MCU yet; pick anything small, inexpensive, and easy to program—ATmega, STM32, ESP32, or s...

I’ve drafted a single-layer board in Altium Designer and now need a seasoned set of eyes to run thorough simulations before I commit to building the first prototype. Your task is to import my project, verify the stack-up and component models, and perform all relevant electrical, thermal, and rule-check simulations available in Altium. Key goals • Confirm that signal integrity and power distribution meet design intent. • Flag any DRC or manufacturing issues early so I can correct them before fabrication. • Produce a concise simulation report summarizing the tests run, key plots or screenshots, and your recommendations. Deliverables 1. Updated Altium project files with all simulation settings preserved. 2. PDF or DOC report of findings and suggested fixes. ...

I am putting together a self-funded, individual project that calls for a fully specified gas-chromatography system fitted with both a Thermal Conductivity Detector (TCD) and a Flame Ionization Detector (FID). The goal is to separate and quantify light hydrocarbons—specifically methane, ethane, ethylene, acetylene and closely related species—in liquid samples that will be injected directly or via headspace. What I need from you: • An end-to-end design covering column selection, carrier gas choice, oven programming and detector configuration so that both TCD and FID work in tandem without signal overlap. • A step-by-step method for sample preparation and injection that delivers sharp peaks and reliable quantitation for the compounds listed above. • Calib...

I need a detailed electrical plan for installing an EV charger in the garage of a new residential home, as required by council regulations. The home has a three-phase electrical supply. Requirements: - Compliance with Woollahra council regulations For condition 14 (Item 37) that requests “electrical plans of all off street parking demonstrating capacity for Level 2 (single phase, 7kw power) charging point” - Detailed schematics for three-phase supply - Specifications for EV charger installation in garage Ideal Skills and Experience: - Experience with residential electrical planning - Knowledge of council requirements for EV charger installations - Familiarity with three-phase electrical systems

I need a compact, production-ready circuit that brings reliable wireless communication to a new consumer-electronics device. The work begins with schematic capture and component selection, moves through PCB layout, and finishes with ready-to-manufacture Gerbers, a complete BOM, and clear test guidelines. The radio link is the heart of the design, so careful RF layout, antenna matching, and regulatory-compliant power levels are essential. Bluetooth LE is my preferred protocol, though I am open to Wi-Fi or other 2.4 GHz solutions if you can demonstrate lower cost or better battery life without sacrificing performance. Please plan on: • Delivering editable design files in Altium, KiCad, or Eagle, plus PDFs for quick review • Calling out any critical components with long le...