Đã Đóng

juice press 6k bar with fea/cfd/sim

Design hpp press and fea and cfd and animation

Milestone1, 50$

Design the water cylinder id66 od maybe 150mm, take a 200ton jack , piston with 20 steel rings from combustion engines, piston stroke500mm, and oil pump and push the piston to produce 6000bar, make fea and cfd and animation.

Milestone2, 50$

Put water cylinder onto 4m tube with traveler (chamber divider with seals like o-rings), design c flanges and caps and 2 valves on each side, let water flow in when juice already fills the whole tube volume, press juice to 6000bar, make fea and cfd and animation.

Milestone3, 50$

Put components around press like air pressure with 4 cylinders controlling the valves, design valves with sealing, choose cylinders: sucking juice and pressing into tube and the one pressing juice out with 10L of water, show interface to bottling station (no oxygen, all ss304 tubes), show system cleaning with water, make fea and cfd and animation.

Milestone4, 50$, optional

I send you links of all machines (washer, mincer, grinder, bottler, power units and cooler) and you integrate them into container. Make film of transparent container showing the whole system.

Milestone5, 50$, optional

2 more tube versions, all 4m, but id 150 and 300mm. make fea and cfd and animation.

I need the plans for all parts that need to be produced, maybe you even find a producer in your country?

General useful data:

You need to show how the juice is filled into the 4m long tube, pushing the chamber divider from right to left. you need to show the hydraulic pump, the 200 ton jack, the water cylinder where 1.75L are pressed to 6000bar while seeing how the water flows into the 4m long tube, compressing the juice, so the divider moves 60cm to the right=15%, and please find a means how to show the enormous pressure. show decompression while 200ton jack moves piston back. Show 10L cylinder pressing water in 4m tube, moving divider to the right, while juice is pressed out. Indicate bottling station. The press is what it s all about. You also have to show the 4 valves (2 at each end of the 4m tube, how they open and close when juice/water flows in/out.

The jack releases pressure after having pressed 1.7L in 4m tube, valve closes. After 3min .during which bacteria is dying-, jack reactivates pressure, when equal to tube pressure, valve driven by air pressure compressor, opens valve, jack piston goes backwards, pressure to zero, vale closes. 10L water cylinder air pressure controlled valve opens, juice out valve opens, juice is pressed out, all valves close, juice in valve opens , juice pressure cylinder presses juice into tube. Cycle recommences.

as for low pressure 10L water cylinder and 10L juice cylinder: PTFE seal is recommended.

Size: 60 50 7mm, Material :PTFE+ stainless steel spring, ie from [login to view URL]

as for 6000bar piston in water cylinder: piston ring producer suggests 20x same rings: 1.4057 X17CrNi16-2, distance between rings 5mm, i recommend same config for traveler.

single action jack from chinese producer.

Kĩ năng: AutoCAD, Autodesk Inventor, Kĩ thuật, Solidworks

Xem nhiều hơn: verification validation fea cfd computational work document, word press edit menu bar top theme, fea cfd hourly rate, translate press release chinese, juice bar posters, fea cfd, design juice bar, juice bar design concept, juice bar concept, real world juice smoothie bar business start, fea cfd service malaysia, fea cfd scope, fea & cfd of a small wind turbine, fea cfd of a small wind turbine, ansys, comsol, fea, cfd, abaqus, catia, ansys, comsol, fea, cfd, abaqus, , ansys, fea, cfd, comsol

Về Bên Thuê:
( 1 Nhận xét ) neuss, France

ID dự án: #21852820

7 freelancer đang chào giá trung bình $162 cho công việc này

mhussein92

please, i want to know if you have a physical model or not and what software you prefer? Hello, I am a mechanical engineer, expert in SolidWorks and have + 5 years of experience in mechanical design. and my master is i Thêm

$200 USD trong 7 ngày
(8 Nhận xét)
3.1
cchcch921

Hi, I 'm Computational Fluid Dynamics expert and have extensive experienced in the numerical simulation by Ansys Fluent . I also have the ability to run numerical simulations with the UDF function. Of course, I have ma Thêm

$250 USD trong 7 ngày
(6 Nhận xét)
2.4
wqdragon

Hi there, I have read through the job details extremely carefully and I am absolutely sure that I can do the project very well. I have rich experience with 6+years in logo design and image processing using Photoshop, Thêm

$140 USD trong 7 ngày
(2 Nhận xét)
2.0
wang1223

Hi there I am Li, senior 2D/3D designer with 8 years of experience. After reading over your job description I have understood what you want. Could you please share the more details with me? I can assure you that I can Thêm

$140 USD trong 7 ngày
(0 Nhận xét)
0.0
nehalgudaliya1

Hello sir, Greetings from Nehal..... We have a small team of an expert engineers. We are doing work in this field since 2016. We can provide you solution in many field like 1) Mechanical engineering # Thêm

$133 USD trong 3 ngày
(1 Nhận xét)
0.0
limbeboy7

this can be done in solidworks including animation and flow simulation. after looking at the pictures you might need to increase the price for the milestones based on the simulations unless you already have the pump po Thêm

$140 USD trong 7 ngày
(0 Nhận xét)
0.0
mustafalathif

Hello, I have intermediate knowledge in CFD and i know how to do simulations in Ansys and Abaqus. I will design your projects as you like.I am new at freelancer.

$133 USD trong 4 ngày
(0 Nhận xét)
0.0