Đã Đóng

Motor Controlled by Proximity Switch, Design & Program.

I have a simple project that I need help with. I have attached a photo showing the layout. I have a battery attached to a gear motor that moves a magnet up and down slide that is attached to a pole. The motor is setup in such a way that the motor only has to run in one direction to accomplish this up and down motion. I want to setup a magnetic proxitmity switch at the top of the pole that will tell the motor to start and stop when it either senses or does not sense the magnet. My thought is that the best way to accomplish this is with a simple microprocessor with simple code that controls the power coming from the battery. It will run a pattern, Here is a breakdown of what I want to happen in the pattern:

1. Magnet in position 1 with proximity 1 recognizing it - Motor stopped.

2. Magnet in position 1 with proximity 1 NOT recognizing it - Motor Running.

3. Magnet in position 1 with proximity 1 recognizing it - Motor stopped.

I will need to be able to adjust the sensitivity of the proximity sensor so that I can get the magnet to stop in the right place. I need the project completed ASAP.

I think it's pretty easy just the correct way to wire it, the programming, and what chip to use are beyond me. I am hoping to find someone who can work on this easy part because our next step is to include a timer and a remote to the next model and would like to use the same person for the next job.

Kỹ năng: Lập trình C, Kĩ thuật điện, Điện tử, Visual Basic

Xem thêm: motor controlled proximity sensor, programming proximity sensor motor, work gear, top programming, best way start programming, person one photo, remote programming job, pretty design, power program, next gear, need help programming project, my wire, motor design program, motion job, motion design job, want start programming, job programming find, step design, help find right job, find remote programming job, find job design, design magnetic, design controls, programming power, beyond design

Về Bên Thuê:
( 1 nhận xét ) Wesley Chapel, United States

Mã Dự Án: #1007197

18 freelancer đang chào giá trung bình $306 cho công việc này

TopGunPk

Hello. Please see PM.

$180 USD trong 2 ngày
(7 Đánh Giá)
4.5
zszabo

Hi, Please see PM, BR Zoltan

$500 USD trong 20 ngày
(3 Đánh Giá)
3.9
GreenlightAV

Please see my message to you.

$240 USD trong 15 ngày
(2 Đánh Giá)
3.9
hcooper84037

Take a look at the offering I have at www.pic-bee.com, this should provide you with a solution for both the first and second stage. It will require a small amount of custom firmware but the hall sensor to detect the m Thêm

$200 USD trong 20 ngày
(1 Đánh Giá)
3.8
alit56

20+ yeas experience in embedded design, especially with PIC uCs.

$200 USD trong 14 ngày
(5 Đánh Giá)
3.6
sbk

please check your pmb

$220 USD trong 4 ngày
(3 Đánh Giá)
3.4
JJdatajobs

Hello 'seventhroom', Please see my PM. Thank you. With regards, JJdatajobs.

$50 USD trong 1 ngày
(5 Đánh Giá)
3.1
adipdutt

Please see PMB

$220 USD trong 7 ngày
(3 Đánh Giá)
3.0
amitj9

Hi, This can be done using a low-cost microcontroller from Micrcohip. I have been working with Microconroller programming and hardware designing since 20 years. This is quite simple to implement. Amit desi Thêm

$250 USD trong 20 ngày
(1 Đánh Giá)
2.4
IoliteTech

Hi, Please Check PM.

$45 USD trong 2 ngày
(2 Đánh Giá)
1.7
AbhaBrajesh1956

I can do your project, Abha

$220 USD trong 30 ngày
(1 Đánh Giá)
1.0
progsel

HI, in the past I already developed littlemunt like this, for sure NOT PROBLEM AT ALL. But I have a question, when the motor is position 1 (motor off) whos start the process? thank you

$500 USD trong 20 ngày
(0 Đánh Giá)
0.0
smartknight92200

'm interested in your project i'll use PIC16f84 micro-controller and IRF740 for motor power control.I'll receive half paid at delivery and the second half will be after testing the circuit and its functionality.

$80 USD trong 4 ngày
(0 Đánh Giá)
0.0
racorage

I have worked with microcontroller based application for 5 years now. I have experience of working with proximity sensors using magnets.

$200 USD trong 10 ngày
(0 Đánh Giá)
0.0
hidalgoem

Hello, I have experience in motor control, see my PM.

$180 USD trong 8 ngày
(0 Đánh Giá)
0.0
dharminec

you will get your project in time.

$2000 USD trong 20 ngày
(0 Đánh Giá)
0.0
sanwal399

hi i am working on the embeded systems for last 10 years . ur project canbe controllerd by microcontroller made by microchip .

$175 USD trong 4 ngày
(0 Đánh Giá)
0.0
YuriMat

Please see pm.

$40 USD trong 2 ngày
(0 Đánh Giá)
0.0