PCB Design for Electronic Wind Monitoring Prototype

Đã Hủy Đã đăng vào 6 năm trước Thanh toán khi bàn giao
Đã Hủy

I am developing an electronic prototype device that will monitor windspeed and direction using an array of air pressure sensors. This prototype will be tested in a wind tunnel. The device will be physically connected by a USB connector to a laptop computer that will display the sensor output and log the sensor readings for later study and analysis.

I have included documentation and links for all the specifications described below.

This project is underway and the work needed here was begun by another Freelance who was unable to compete the project.

Deliverables

First Deliverable: Design 2 small PCBs

The first PCB will hold 3 air flow sensors (I2C) mounted side by side with a 4.7k Ohm pull-up resistor on each sensor's SCL and SDL outputs. The resistors need to be easily hand soldered and the values may need to be changed on occasion so the design will need to accommodate this possibility. The back of the board will have a wire-to-board-connector that will allow the first board to connect to the second board. The connectors should be mounted to minimize the overall profile effect of the wiring. There is an included graphic that shows the height and width alignment of the sensors. The boards should be designed to minimize the height and width dimensions.

The second PCB will hold two Adafruit breakout boards on one side and an Arduino Nano on the other. The USB plug on the Nano should be accessible through a window on the side of the case. Case design is not part of this project. Again, the connectors should be mounted to minimize the overall profile effect of the wiring.

The two boards will be mounted back-to-back in a case such that with spacers and mounting screws they become a single component.

Note: The reason I am asking for this design is that I plan on adding additional electronics in the future. By having the sensors on one board and the electronics on another I can more easily change the electronics without disturbing the sensors.

Second Deliverable: Modify existing code or create new code that will allow the sensor output to be monitored on an attached computer and the data stream logged in a text file.

The Arduino Nano will be connected to a laptop computer via USB cable. I will need to be able to start and stop data monitoring and logging as needed as well as set the intervals at which the sensor output is delivered to the monitor and log. The log also needs to contain a timestamp.

It is likely that after some usage and testing of the device I might have some software modification requests and would like the programmer to be available for follow-up.

Electronics Schematic

The included schematic was originally designed without using breakout boards. The modifications needed to accommodate the breakout boards are noted on the schematic

Parts List

3 Omron D6F-PH sensors

- D6F-PH0505AD3 (2)

- D6F-PH0025AD1 (1)

- Datasheet: [login to view URL]

- CAD download: [login to view URL](S(0zupvrm10z0fcrwbzy25vm0b))/[login to view URL]

Breakout Boards

- Adafruit 2717: TCA9548A - I2C Multiplexer (1)

- Adafuit 395: TXB0108 - 8-channel Bi-directional Logic Level Converter (1)

Arduino Nano (1)

4.7k Ohm resistor (6)

Wire-to-Board-Connectors (as needed)

Kĩ thuật điện Điện tử Vi điều khiển PCB Layout Thiết kế sản phẩm

ID dự án: #15838698

Về dự án

20 đề xuất Dự án từ xa 6 năm trước đang mở

20 freelancer chào giá trung bình $93/giờ cho công việc này

MikroStar

Hello, I am an Embedded system developer and Product Design Engineer.I have extensive experience in Design of Electronics and embedded System Design. I have expertise in PCB Design and also Firmware development.I have Thêm

$100 USD / giờ
(82 Nhận xét)
7.9
ahmedmohamed85

A proposal has not yet been provided

$33 USD / giờ
(239 Nhận xét)
7.3
hash92PCB

I am an electronics R&D engineer, i have designed circuits and built many boards, will be happy to help you get your design done quickly. Contact me please.

$33 USD / giờ
(13 Nhận xét)
5.9
aluciano710

I can definitely get the two boards completed for you but will need to see the schematic noted in the post in order to assure the correct pinouts for communication with the Arduino. It doesn't come up as an attachment Thêm

$35 USD / giờ
(2 Nhận xét)
3.9
injetec

Greetings, I'm an experienced embedded device programmer(PIC microcontrollers ),Arduino programmer, hardware designer, PCB designer (Eagle CAD). I understood your project at all, it uses 3 Differential pressure Sens Thêm

$60 USD / giờ
(1 Nhận xét)
3.4
Itblast

NO COPY PASTE BID LIKE OTHER SELLERS... !!! Please Read My Proposal For One Time !!!! I am having 6+ years of experience In This kind of Project. I Have Recently Completed Similar Project.. . . .

$41 USD / giờ
(0 Nhận xét)
0.0
ngothiep127

A proposal has not yet been provided

$41 USD / giờ
(1 Nhận xét)
0.2
mrisso256

I have a lot of experience with I2C. I have a lot of successful product in the field. I have been doing hardware design for a long time so I know what works and what doesn't. I do a lot of contract circuit design and P Thêm

$41 USD / giờ
(0 Nhận xét)
0.0
omarahmad81

A proposal has not yet been provided

$38 USD / giờ
(0 Nhận xét)
0.0
kapilb

I am using diptrace and Eagle for pcb design and doing for the last 6 years. I have designed 200projects industrial and academic

$33 USD / giờ
(0 Nhận xét)
0.0
ldamiendesilva

Dear Sir/Madam, I am a second year Computer Systems Engineering Student at Sri Lanka Institute of Information Technology-Malabe folowing the Curtin University pathway. At the moment we are on holidays therefore I have Thêm

$27 USD / giờ
(0 Nhận xét)
0.0
joanarno

I saw your design and I think it mus be slightly changed because the level adaptor doesn’t work with I2C. I can make 2 boards one with the sensors and another to connect to the arduino nano with the adafruit board or t Thêm

$1111 USD / giờ
(0 Nhận xét)
0.0
enmanuellandrade

my last work in arduino was: internships carried out in the Automation, Information Technology and Telecommunications (AIT) department of the Táchira PDVSA region, carrying out the project called DEVELOPMENT OF AN ARDU Thêm

$27 USD / giờ
(0 Nhận xét)
0.0