
Closed
Posted
Paid on delivery
I’m building a compact control panel that combines an ESP32 core, a membrane keypad, and a 3.5-inch TFT LCD. I already have functional requirements and rough block diagrams; what I now need is the full electronic design, ready for manufacturing. Scope • Power architecture: single regulated 5 V input with the necessary step-downs and filtration for the ESP32’s 3 V3 rail, back-light drive, and any aux lines. • Digital section: ESP32 module or bare chip with all pins broken out for firmware flashing, reset, and debugging. • Interfaces: matrix keypad connector and ESD protection, 8/16-bit TFT LCD interface, plus level-shifting where required. • Communications: I²C, SPI, and UART brought to headers for external sensors and future expansion. • Miscellaneous peripherals: buzzer driver, status LEDs, spare GPIO header, and on-board programming port. • Design-for-manufacture: component footprints matched to current availability, clear silkscreen labelling, and assembly notes. Deliverables 1. Complete annotated schematic in your preferred CAD package (Altium Designer, KiCad, or EasyEDA are all acceptable). 2. Cleanly laid-out, two-layer (or more if necessary) PCB with controlled trace widths for high-speed lines to the TFT. 3. Manufacturing outputs: Gerber files, NC drill, pick-and-place, PDF schematic, and full BOM with supplier links. 4. Brief design report covering key calculations (power budget, decoupling, back-light current) and pin mapping. Acceptance criteria • All ESP32 pins configure without conflicts and meet datasheet guidelines. • 5 V rail remains within ±5 % under 500 mA load. • No air-wires or DRC errors in final Gerbers. • BOM components must show at least two active distributors in stock. If you have recent experience with ESP32-based boards and TFT interfaces, I’d love to see a sample or screenshot of previous work when you reply.
Project ID: 40761014
38 proposals
Remote project
Active 6 hours ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
38 freelancers are bidding on average ₹8,487 INR for this job

As an electrical engineer with a vast experience in electronic design, I believe I am well-suited for your project. My knowledge of power architectures and digital sections, along with my proficiency in PCB layout in Altium, enables me to create circuits that are not only efficient but also easily manufacturable. Additionally, my previous work on low-power distribution and simulation of circuits would be particularly beneficial in meeting your project requirements for the 5V rail's stability and the absence of errors in Gerber files. Moreover, my expertise extends to embedded systems - that's where I have had intimate experience with ESP32-based boards like yours. I've worked with ESD protection, TFT LCD interfaces, and various communication protocols (I²C, SPI and UART). Furthermore, my familiarity with Altium Designer, KiCad and EasyEDA means I'm flexible enough to work within your preferred CAD package. In conclusion, my skills in electronic design and PCB layout paired with my previous hands-on experience with ESP32-based projects make me an ideal candidate for your project. By choosing me for the job, you can expect not only clean schematic designs, efficient PCB layouts but also a complete professional deliverable package including Gerber files, NC drill outputs and BOMs. Let's leverage my competencies to bring your compact control panel to life!
₹12,500 INR in 10 days
7.5
7.5

Hi, I have experience in designing Circuits and can complete your project. I have expertise in the following: 1- Designing schematic and PCBA 2- Ordering the PCBA and getting boards manufactured. 3- Writing firmware for the PCBA to make sure everything works as expected. 4- I can also develop smartphone apps to communicate and control the hardware. If you wish we can discuss in chat. Thank you.
₹7,000 INR in 7 days
7.4
7.4

With over 8 years of experience in Electrical Engineering and PCB design, I consider myself uniquely qualified to handle your project. In addition to my vast experience, I am also familiar with the ESP32 and TFT interfaces you're employing and have successfully designed similar systems in the past. Allow me to highlight some of my notable qualifications: professioal EasyEDA desginer, proficient in Altium Designer, KiCad and Eagle; well-versed in MATLAB/SIMULINK, Python programming and VHDL/Verilog HDL. All these skills combined make me an ideal candidate for the demands of your project. My approach to work is clear and systematic. I will ensure each requirement laid out is met diligently, from power architecture with necessary step-downs to controlled trace widths for high-speed lines used for TFT. My designs prioritize not only functionality but also manufacturability ensuring that your BOM components will be readily available from active distributors. Customer satisfaction is my utmost priority which is why I'm committed to providing revisions until you are completely satisfied. My passion for PCB design drives me to deliver exceptional results within timeframes and budget considerations and earning the title of "Preferred Freelancer". Let's connect soon to discuss this project further or feel free to check out my portfolio to see more examples of my exceptional work. Looking forward to turning your ideas into reality!
₹7,000 INR in 7 days
6.9
6.9

Hey there! I’m Alok, A PCB, Circuit and Mechanical designer with a passion for turning ideas into rock-solid, high-performance circuit boards. even expert on Python, C, C++ With nearly a decade of experience, I’ve tackled everything from compact consumer gadgets to complex industrial systems—always with a focus on precision, efficiency, and reliability. # Schematic & Layout Design – Clean, optimized, and manufacturable. # Component Selection & Library Management – No surprises, just the right parts for the job. # Reverse Engineering – PCB cloning, replication, and improvements. # Gerber, BOM & CPL Generation – Ready for seamless production. # DFM & DFA Expertise – Because great design means smooth manufacturing. # Multi-Layer, Flex, & High-Density PCB Design – Whatever the project needs. If you need a PCB and Code that’s efficient, reliable, and built for real-world performance, let’s chat. I’d love to help bring your project to life!
₹16,500 INR in 7 days
6.0
6.0

Hello, I’m a Hardware Design Engineer with experience designing ESP32-based IoT and industrial control boards, including power management, protection circuits, communication interfaces, and manufacturing-ready PCBs. I can handle your project from schematic design to a production-ready PCB, including: * 5V input power architecture and stable 3.3V regulation. * ESP32 programming, reset, and debugging interfaces. * TFT LCD and membrane keypad integration, including level shifting and ESD protection where required. * I²C, SPI, UART, buzzer, LEDs, and expansion headers. * PCB layout, component availability verification, DRC checks, Gerbers, pick-and-place, and a complete BOM with supplier links. I’ll also verify the power budget, ESP32 pin assignments, and TFT signal routing to ensure a reliable, manufacturable design. I can share relevant ESP32 and industrial control PCB designs from my portfolio. Best regards
₹7,000 INR in 7 days
5.6
5.6

Having designed and built numerous IoT devices, including those with ESP32-based boards and TFT interfaces, I am confidently equipped to take on your project. I understand the intricacies that come with delivering a compact control panel that integrates several components, and can successfully manage all aspects of the design-for-manufacture process. As a professional adept in using Altium Designer, KiCad, and EASYEDA, I assure you of precise design implementation with clean layout PCB and controlled trace widths for high-speed lines for the TFT. One of my core strengths as part of a complete web and mobile stack engineer is integrating AI on edge devices like the ESP32—acting on live sensor data and within ERP workflows. Combining this expertise with my electrical engineering skills make me an ideal fit for your project.
₹7,000 INR in 7 days
5.1
5.1

Hi, I’ve carefully read and understood the requirements. I have hands-on experience with ESP32-based hardware, TFT interfaces, power management, and custom PCB design. I can handle the schematic, ESP32 pin mapping, TFT and keypad interfaces, power regulation, ESD protection, and complete manufacturing files, including Gerbers, BOM, and pick-and-place. You can also check my portfolio for my previous ESP32 and multilayer PCB projects. Best regards, Ahmed
₹7,000 INR in 7 days
4.6
4.6

Hi, at HardFault, we have an in-house electronics and PCB design team experienced in ESP32-based hardware, power management, display interfaces, and manufacturing-ready PCB development. We can take your block diagrams and functional requirements through to a complete, production-ready design, including the annotated schematic, PCB layout, firmware programming and debugging interfaces, TFT LCD connections, keypad protection, and I²C, SPI, and UART expansion headers. We’ll pay close attention to power budgeting, backlight drive, signal integrity, decoupling, and GPIO allocation to avoid boot-strapping or peripheral conflicts. Our deliverables will include the complete CAD files, Gerbers, drill files, pick-and-place data, assembly-ready BOM with supplier links, and a design report covering power calculations and pin mapping. We’ll also verify the design against the specified DRC rules and check component availability across at least two distributors before finalizing the BOM. With our team handling the complete process in-house, you’ll have coordinated support from schematic design through manufacturing handoff rather than relying on an individual freelancer. Could you share which exact 3.5-inch TFT module you plan to use, including its controller and interface type, so we can determine the right pin mapping, level shifting, and backlight power architecture from the start?
₹7,000 INR in 7 days
3.6
3.6

Hello, I am Santosh Chaulagain, a professional Electrical Engineer and PCB Designer with over 7 years of experience in schematic design, PCB layout, and embedded systems, including ESP32, IoT devices, analog and digital circuits. I have successfully completed multiple projects for clients worldwide, delivering reliable and manufacturable designs. I have carefully reviewed your project requirements and I am confident that I can provide a high-quality solution tailored to your needs. My expertise includes PCB design using industry standards, component selection, BOM preparation, Gerber generation, and design optimization for cost and performance. I always ensure that my designs are fabrication-ready and tested for reliability. I focus on clear communication, timely delivery, and customer satisfaction. I am happy to discuss your project in detail and provide revisions until the final result meets your expectations. Looking forward to working with you. Best regards, Santosh C. Electrical Engineer | PCB Designer | ESP32 & IoT Specialist
₹4,500 INR in 7 days
3.8
3.8

I have experience in end-to-end PCB design, including schematic development, component selection, PCB layout, design rule checks (DRC), and Gerber file generation. I can work on circuit design, component footprints, routing, and preparing manufacturing-ready files. My focus is on accurate designs, proper component placement, and reliable PCB performance. Your scope is clear — ESP32, membrane keypad, 3.5" TFT, and a full manufacturing package. This is exactly the kind of board I build. Here's what I bring to this: → I've shipped ESP32 boards with TFT interfaces, including a 3.5" display controller with relay drivers and WiFi control, plus an ESP32-C3 air quality monitor with UART sensor and I2C OLED on one PCB. → Power architecture is where most boards fail — I design the 5V to 3V3 step-down, backlight driver, and decoupling so the rail holds within ±5% at 500mA, exactly your acceptance criteria. → Full stack in-house: schematic, 2-layer layout with controlled impedance on TFT lines, Gerbers, NC drill, pick-and-place, BOM with two live distributors verified per part, and a design report with power budget and pin mapping. → I use KiCad or Altium, whichever you prefer, and I'll send screenshots of previous ESP32 boards with my reply. My approach: → First, review your block diagrams and lock the pin map so no ESP32 conflicts exist before layout starts. → Finally, deliver Gerbers, BOM, PDF schematic, and the design report, with a DRC-clean board and no air-wires.
₹6,000 INR in 3 days
3.5
3.5

Hello, Before designing your ESP32 control panel, I would first verify the GPIO allocation. A 16-bit parallel TFT interface can consume many ESP32 pins, especially when combined with a matrix keypad, SPI, I²C, UART, and programming/debug connections. I would also check the 5V/3.3V power budget, ESP32 current peaks, TFT backlight requirements, and whether a 2-layer PCB can reliably support the selected display interface. My approach: 1. Review your block diagrams and confirm the exact ESP32 and TFT controller. 2. Prepare the complete schematic, pin mapping, and power calculations for your approval. 3. Design the PCB with proper decoupling, ESD protection, and manufacturable footprints. 4. Deliver editable KiCad/Altium files, Gerbers, NC drills, BOM, Pick-and-Place, and a brief design report. Three questions: - Which ESP32 variant and TFT controller are you using? - Is the display interface fixed at 16-bit, or is 8-bit acceptable? - Does the 500mA power requirement include the TFT backlight and ESP32 Wi-Fi operation? I have worked on ESP32-based multilayer PCB designs and can share a relevant layout screenshot. Best regards, Hamza El Amraoui
₹9,000 INR in 6 days
2.8
2.8

As an experienced embedded systems engineer with comprehensive knowledge in PCB design and a proven track record of developing products from conception to completion, I am confident that I am the best fit for your project. I have extensive experience in designing boards using Altium, which aligns perfectly with your requirement. My proficiency spans across various microcontrollers like ESP32, nRF52, STM32, and my expertise in power architectures and peripheral interfacing can ensure a high degree of precision and efficiency in this project. What sets me apart is that I take complete ownership of the entire product development cycle. In addition to my PCB design skills, I offer firmware development (especially with ESP-IDF, FreeRTOS), Windows C# applications, and mobile app development using both Flutter and Android native (Kotlin/Jetpack Compose). With this end-to-end understanding of hardware and software integration, there will be no gaps or compatibility issues between your control panel's electronic design and its eventual functionality. Moreover, my experience in delivering complex projects within tight deadlines has taught me the value of open communication and meticulous attention to detail. You can count on me not only to meet but exceed your expectations. Let’s work together to transform your functional requirements and rough block diagrams into a highly functional control panel that leaves no stone unturned.
₹7,000 INR in 7 days
2.8
2.8

Your ESP32 plus 3.5" TFT panel with a membrane keypad is exactly the kind of board I enjoy building, and your block diagrams mean we can move straight into schematic work. → I recently designed a custom ESP32-C3 air quality monitor PCB with TFT/OLED display, power management, and MQTT firmware, delivered as working fabricated units. → I'll deliver annotated schematic, two-layer PCB with controlled-width TFT lines, Gerbers, NC drill, pick-and-place, BOM with two live distributors, plus a power budget report. → Full design, firmware, and enclosure under one roof if you need it later.
₹5,000 INR in 4 days
3.0
3.0

Hi, I can help design a complete, manufacturing-ready ESP32 control-panel PCB integrating a membrane keypad, 3.5-inch TFT LCD, power regulation, and expansion interfaces. Proposed Approach Review the requirements, block diagram, and TFT datasheet. Design the ESP32 circuit with programming, reset, and debugging interfaces. Implement the 5V input, 3.3V regulation, filtering, and TFT backlight power circuitry. Integrate the membrane keypad connector with suitable ESD protection. Design the TFT interface with level shifting where required. Add I²C, SPI, UART, GPIO headers, buzzer driver, and status LEDs. Create a clean PCB layout with suitable trace widths, test points, and silkscreen labels. Perform ERC/DRC checks and review component availability from multiple distributors. Deliverables Complete annotated schematic Editable KiCad, Altium, or EasyEDA project files PCB layout and Gerber files NC drill and pick-and-place files BOM with supplier links PDF schematic and assembly notes Power calculations and GPIO pin mapping ERC/DRC and manufacturing review report
₹10,000 INR in 7 days
2.3
2.3

I regularly design ESP32-based embedded HMIs and industrial control panels in KiCad and Altium Designer, integrating TFT displays, matrix keypads, and mixed-signal peripheral buses. Designing a reliable control panel around a parallel TFT interface and an ESP32 requires careful GPIO multiplexing to avoid bootstrapping conflicts, clean power distribution under load steps, and low-inductance return paths for high-speed display bus signals. I will convert your block diagrams into a full schematic, implementing a stable 5V-to-3.3V step-down regulator stage designed to maintain tighter than ±5% regulation across 500mA+ transient loads. The design will include an active constant-current backlight driver, multi-channel ESD clamping (USBLC6/array) on the keypad FPC connector, dedicated level-shifting if needed for the 3.5-inch panel, an auto-reset circuit for USB flashing, and isolated routing for external I2C, SPI, and UART headers. For the layout, I will route a 2-layer or 4-layer board with continuous reference ground planes, length-matched TFT data lines, and strict multi-layer antenna keepouts. The BOM will feature 100% active, in-stock parts cross-verified on Mouser and LCSC. Deliverables include native CAD files, production-ready RS-274X Gerbers, NC drill data, CPL pick-and-place files, a verified BOM with distributor links, and a concise engineering design report detailing the power budget and pin mapping.
₹12,500 INR in 6 days
0.9
0.9

Hello, I’m an embedded hardware designer with recent experience in STM32-based drone controllers with TFT displays, and in KiCad designs using ESP32, SPI/I²C/UART peripherals, and multi-rail power (buck/boost regulators, battery charging). For your control panel I would deliver: Power: 5 V input protection and filtering, a 3V3 buck sized for ESP32 peaks, and a constant-current PWM backlight driver. The 5 V rail will be verified within ±5 % at 500 mA. Digital: ESP32 (I recommend an ESP32-S3 for the 8/16-bit parallel TFT), with USB/UART programming, EN/BOOT buttons and a debug header. The pin mapping will avoid strapping and reserved-pin conflicts. Interfaces: matrix keypad connector with ESD protection, 8/16-bit TFT interface with controlled traces, and I²C/SPI/UART, spare GPIO, buzzer and LED headers. Manufacturing outputs: KiCad schematic and PDF, a two-layer PCB with DRC/ERC clean, Gerbers, drill, pick-and-place, BOM with supplier links (two distributors in stock per part), and a short design report. To start, could you tell me the TFT controller (e.g. ILI9488/ST7796), the keypad size, and the board size limit?
₹10,000 INR in 7 days
0.4
0.4

✔ I deliver 100% work — 99.9% is not for me. ✔ Workflow Diagram ⟶⟶ Requirements Review ⟶⟶ ESP32 Pin Mapping ⟶⟶ Power Architecture ⟶⟶ Schematic Design ⟶⟶ TFT/Keypad Integration ⟶⟶ PCB Layout ⟶⟶ ERC/DRC Validation ⟶⟶ Gerbers & BOM ⟶⟶ Documentation Key Highlights I can start with a free preliminary schematic review and ESP32 pin-mapping sample to demonstrate the proposed design approach before proceeding. I'll develop a manufacturing-ready PCB in KiCad, Altium, or EasyEDA, aligned with your functional requirements, block diagrams, and ESP32 datasheet guidelines. The design will cover regulated 5V/3.3V power, TFT 8/16-bit interfacing, keypad ESD protection, level shifting, programming/debugging, and I²C/SPI/UART expansion. I'll integrate buzzer drivers, status LEDs, spare GPIO, decoupling, backlight control, and clearly labeled connectors. PCB routing will prioritize signal integrity, grounding, thermal performance, and manufacturability. Deliverables include annotated schematics, PCB source files, Gerbers, NC drills, pick-and-place, PDF schematics, supplier-linked BOM, and design calculations. I'll verify ERC/DRC, pin conflicts, and component availability across two distributors. Please share your diagrams and TFT controller details. Timeline, budget, and milestones can be discussed after our chat begins. Best Regards, Asad ESP32 | PCB Design | Embedded Systems | Hardware Engineering
₹3,000 INR in 3 days
0.0
0.0

I can turn your ESP32, membrane keypad and 3.5 inch TFT requirements into a manufacturing package with schematic, PCB, fabrication files, BOM and design report. I’d confirm the exact TFT interface and ESP32 module first, then check power and pin mapping before routing the board. The work covers the regulated 5 V architecture, protected keypad and display interfaces, expansion headers, buzzer and LEDs, a two layer layout, DRC, Gerbers, drill and pick and place files, PDF schematic, BOM and assembly notes. I’ll include the requested power budget, decoupling, backlight current and pin map, plus one bounded acceptance revision. I can’t substantiate recent ESP32 board experience or provide a comparable published screenshot. Acceptance checks will include no unrouted nets or DRC errors, 5 V within ±5 percent at 500 mA, datasheet based pin checks, and two listed distributors in stock when the BOM is checked. Which exact TFT model or controller and keypad pinout should I use? I’ll start after award, a funded milestone and receipt of those specifications. Delivery: within 96 elapsed hours (4 calendar days) after funded kickoff and receipt of the required access and materials.
₹6,501.99 INR in 4 days
1.5
1.5

Halo, Saya tertarik mengerjakan desain elektronik panel kontrol ESP32 Anda, dari skematik, layout PCB, hingga file manufaktur yang siap produksi. Saat ini saya sedang mengembangkan proyek lampu pintar berbasis ESP8266. Proyek ini mencakup kontrol Wi-Fi, pengaturan kecerahan dengan PWM, driver beban (MOSFET/relay), dan catu daya 5 V yang stabil. Pengalaman ini langsung relevan dengan kebutuhan Anda, terutama untuk arsitektur daya, penanganan pin mikrokontroler, dan desain yang ringkas serta andal. Untuk proyek Anda, saya akan menyiapkan: Daya: input 5 V dengan proteksi, regulator 3V3, dan driver lampu latar TFT. Digital dan antarmuka: ESP32 dengan port pemrograman, TFT 8/16-bit, keypad membran dengan proteksi ESD, serta header I²C/SPI/UART. Hasil akhir: skematik beranotasi, PCB dengan DRC bersih, Gerber, pick-and-place, BOM dengan minimal dua distributor, dan laporan desain berisi pin-map serta perhitungan daya. Saya bisa mengirimkan screenshot skematik dan foto proyek ESP sebagai contoh pekerjaan. Sebelum mulai, saya ingin memastikan beberapa hal: apakah TFT berupa modul siap pakai atau panel mentah, dan apakah ESP32 berupa modul atau chip kosong? Terima kasih, saya siap berdiskusi lebih lanjut. Hormat saya, khai
₹7,000 INR in 8 days
0.0
0.0

Hi, Looking for an experienced technology partner to turn your concept into a reliable, production-ready product? We can help. Greetings from OSTronik India, we are specializing in Power Electronics, PCB Design, Embedded Systems, Firmware, IoT, AI Integration, and Mobile Application Development. Our Expertise ⚡ Power Electronics DC-DC & AC-DC converters, power supplies, power management, voltage/current regulation, protection, isolation, switching circuits and customized power solutions. ? PCB & Hardware Multilayer PCB design, schematic development, component selection, BOM preparation, Altium Designer, EMI/EMC considerations and production-ready files. ? Embedded & Firmware STM32, ESP32/ESP8266, PIC, AVR, Raspberry Pi, Embedded C/C++, sensor interfacing, hardware integration, debugging and optimization. ? IoT & Communication UART, SPI, I²C, CAN, RS-485, Modbus, MQTT, Wi-Fi, BLE, LAN, cloud connectivity and real-time monitoring. ? Mobile Applications Custom Android & iOS applications for device control, monitoring and data visualization. We can take your project from concept → design → prototype → testing → production, with a focus on reliability, performance and cost efficiency. Share your requirements or existing files, and let’s discuss how we can bring your product to life. Best Regards, Team OSTronik India Empowering Innovations
₹7,000 INR in 7 days
0.0
0.0

Bengaluru, India
Member since Aug 28, 2022
₹600-1500 INR
₹1500-12500 INR
$80 USD
₹600-1500 INR
$25-50 USD / hour
₹1500-12500 INR
$5000-10000 USD
₹1500-12500 INR
₹600-1500 INR
₹750-1250 INR / hour
₹600-1500 INR
₹1500-12500 INR
$250-750 USD
₹1500-12500 INR
$30-250 USD
$10-30 USD
$10-30 USD
$30-250 USD
£250-750 GBP
$10-30 USD
₹12500-37500 INR
₹12500-37500 INR