Đã hoàn thành

Electrical Project

I have a very easy project to for someone with electronic experience. I need a schematic made for a USB charger connected to a battery. I will need all the correct electronic components listed out in a Bill of Materials with there specs, Including fuses, wire size, what wires go to what pin-outs, and any other electronic parts needed

**** (I want more then an Inline Fuse, to the USB port and Jumper Pins 2&3 to make the phone think it is charging in AC mode, There is a reason for the additional electronics inside car chargers and I would like this to be explained and to be used in this product.)**** This is a requirement*****


1. Must be able to charge two I-Pads Simultaneously without the message appearing on the I-Pad "Plugged in but not charging" (Required)

2. If you know how setup a Rapid Charge System EVEN better (Optional)

[url removed, login to view] system should not short out any USB electronics. (Required)

Details of the Project:

TWO USB Female Ports (10 Watts) each I believe to prevent the I-Pad message from popping up "Feel Free to Correct ME")

Battery: Voltage: 12V Capacity: 11AH CCA or Cold Cranking Amps: 120

You design everything required in-between to meet the criteria above.

Deliverables: One complete Schematic with BOM and all pin-out locations from where the fuse goes to where to attach the wires to the USB port.

Additional - Please do not send me a message saying "I can complete this for you" Giving me no more information then that. Please tell me enough info about about yourself so I am confident in your ability to generate the requirements above. I will answer any question if you would like to know more about the full system that this is being plugged into. Also please let me know why I should chose your bid

*** Note: this is a very simple project and should not be bid over $100 in the fact that this should only take about an hour or two to complete and I can also purchase a pre-existing system to reverse engineer this from for about $45. (Trying to save time of purchasing and reverse engineering the system myself) ****

Kĩ năng: Kĩ thuật điện, Điện tử

Xem nhiều hơn: why you want to be an engineer, why do you want to be an engineer, why do i want to be an engineer, what to take if you want to be engineering, what is needed to be an engineer, what is electronic engineer, what is be electrical engineering, tell me more about yourself, tell me about yourself question, tell me about yourself answer, tell me about myself, tell about yourself, so tell me about yourself, requirements needed for engineering, requirement for electronic engineer, required electronics engineer, note pad design, need the fact of engineer, need electronic engineer, need electrical engineering, needed electrical engineer, need a electronic engineer, make 100 an hour, i want to know more about electrical engineering, i want to be an electrical engineering

Về Bên Thuê:
( 1 Nhận xét ) Kernersville, United States

ID dự án: #1711126

Được trao cho:


Hi, I am experienced in electronics, and I can definitly fulfill your requirements. Please see PM.

$200 USD trong 30 ngày
(2 Đánh Giá)

8 freelancer đang chào giá trung bình $166 cho công việc này


hi, i can help.

$450 USD trong 30 ngày
(41 Nhận xét)

It will be done.... Try Me...

$99 USD trong 5 ngày
(1 Nhận xét)

Read Pm sir :)

$70 USD trong 2 ngày
(1 Nhận xét)

My greetings, Please see private message. thanks in advance.

$30 USD trong 1 ngày
(0 Nhận xét)

Hello Good Morning I am employee at power conditioning equipment manufacturer company. I am working as R&D and testing engineer in this company. And i know very well that you need a smps Charger only with specifi Thêm

$110 USD trong 30 ngày
(0 Nhận xét)

I have similar in my jeep, It is wired in to the 24VDC system and delivers the approx required voltage to 4 USB outlet to power the speakers, and charge upto 3 phones, it will also drive any USB powered device such as Thêm

$250 USD trong 30 ngày
(0 Nhận xét)

Dear Sir, We are Reserach and Development company whose working area are : -Digital Motor Control -Analog Design -Electronic Design -Power Electronics -PCB design -Embedded system -Matlab -Simulation of ha Thêm

$120 USD trong 3 ngày
(0 Nhận xét)