Đã Đóng

Laser Driver Design

- 2 and 4 channel design (please also see bottom about a stacked design, modular)

- max 2500mA to 3000mA current (adjustable with pot-meter).

- 5 - 24V input

- BIAS adjustment for beam suppression =

- analogue modulation min 100kHz. Will you be using LM317?

- Switch for continuous mode so laser module can be setup without having anything attached to it. (basically a 5V signal on the analog)

- beam suppression (for blue lasers on/off with jumper).

- solder less connectors molex? for easy installing (please let me know what you think, you are the expert on this.

- optional easy to fit heat sink(s).

- small size circuit board.

- measure points for V and A with molex or other terminals per channel of the driver. So i can read this with a arduino later.

- clean signal for the modulation.

Ideas, if possible

- is it possible to use digital pots or an IC for bias and current adjustment, so i could hook up a computer to do it.

- is it possible to build a stacked version of the driver, so i could add channel at one time, so you have a motherboard and add on channel as needed, 1, 2, 3, 4max

- what is the max length of the cable going to the diode itself.

Kỹ năng: Kĩ thuật điện, Điện tử, Vi điều khiển, PCB Layout

Xem thêm: digital signal, laser driver design, the design pot, modular design, i beam design, heat sink design, beam design, what is digital design, small microcontroller, arduino expert, microcontroller design, microcontroller circuit design, microcontroller analog, laser, IC Design, digital circuit design, design circuit, beam, arduino current/, arduino circuit design, arduino 4*4, analogue, analog circuit , arduino laser diode, circuit arduino

Về Bên Thuê:
( 1 nhận xét ) Los Angeles, United States

Mã Dự Án: #4550308

10 freelancer đang chào giá trung bình $588 cho công việc này

MikroStar

hi, i am an electrical engineer and an embedded system designer. i can help you with this project.

$1000 USD trong 18 ngày
(47 Đánh Giá)
6.5
quang102

hello i can do that thanks

$555 USD trong 15 ngày
(16 Đánh Giá)
5.3
betaenergy

Dear Sir, We are Reserach and Development company whose working area are : -Digital Motor Control -Analog Design -Electronic Design -Power Electronics -PCB design -Embedded system -Matlab -Simulation of ha Thêm

$526 USD trong 3 ngày
(16 Đánh Giá)
4.8
shahbaz1980

hello check your PMB.

$744 USD trong 20 ngày
(8 Đánh Giá)
3.7
TheNanoTube

Hi, I have experience with power control, LEDs and microcontrollers!

$533 USD trong 18 ngày
(1 Đánh Giá)
3.2
ecadpcb

Hi, Good day I can work on your project, I can work for you, I offer editing in Altium layout, schematic, pcblayout, billl of materilas (Newark, Digikey, Mouser) and Gerber Files for manufacturing. PCB Layout, IPC, Thêm

$666 USD trong 7 ngày
(1 Đánh Giá)
2.5
DamithaKD

Please Read Pm sir :)

$555 USD trong 3 ngày
(1 Đánh Giá)
1.8
EuroTechGuy

Hi. Please check your PM box. Thanks

$555 USD trong 15 ngày
(1 Đánh Giá)
0.0
XtremeEHS

Hi, do you need it full digital?

$444 USD trong 3 ngày
(0 Đánh Giá)
0.0
Moujahid

I'm very interested in this offer; Please check my profile

$555 USD trong 6 ngày
(0 Đánh Giá)
0.0
holetrontech

I can help you in doing this. check my portfolio...

$277 USD trong 15 ngày
(0 Đánh Giá)
0.0