Development single board radar with a narrow beam long range 100m+

Đã Đóng Đã đăng vào 2 năm trước Thanh toán khi bàn giao
Đã Đóng

Please do not send a generic message, answer the project details.

Development and design of turnkey system components in a single embedded board. An electronic board plus basic configuration software.

The expectation is to design a circuit that uses boards/chips/circuits/systems that exist in western sources like Mouser, Digikey and etc. Would be used in the USA, Canada, Latin America and if possible can pass or avoid FCC certification by using components or design that does not need one.

It should detect at least 100m or more.

The purpose of the project is: To install a radar with a narrow beam that can detect human movement crossing the narrow beam from left to right or right to left, apply an algorithm to rain, snow, avoid birds, small animals, branches waving in front of it.

The radar would have software to visualize its signal area and detection, will have sensitivity adjustment and possible detection type adjustment, have a UART and I/O inputs/outputs.

ANSWER SPECIFICALLY:

1. Do you know or have specific experience with radar development? have you read my requirement in detail and understood what I would like to do? If you please ask clarification questions

2. FCC certification - do you know how to design a board that doesn't need one or can pass it easily?

3. Is it pulse doppler or CW radar? You have to determine if I need to locate how far from the radar it is and how fast it's crossing the radar to filter fast-moving objects like birds

4. What should be the frequency range of radar? You have to determine what would be best. mmWave radar?

Please describe exactly which chip or boards would you use for this project, how would you solve this issue?

You do a full design, manufacture the prototype, test it and provide me with a full board design, firmware and configuration software

Điện tử Kĩ thuật điện Vi điều khiển Kĩ thuật RADAR/LIDAR

ID dự án: #33340608

Về dự án

9 đề xuất Dự án từ xa 1 năm trước đang mở

9 freelancer chào giá trung bình $23/giờ cho công việc này

avigupta0061

Best PCB Design Expert at your doorstep! Dear Client, I can develop single board radar with a narrow beam long range 100m+ as per your requirements I have already designed countless PCBs on radar and am 100% confident Thêm

$25 USD / giờ
(51 Nhận xét)
7.6
faizanmaqbool695

Hi there, I have read your project description and I am confident about your project I can do perfectly. Please leave a message on my chat so we can discuss the budget and deadline of the project. Thanks. regard , fa Thêm

$25 USD / giờ
(45 Nhận xét)
5.9
hsh564cf84accd96

Hi my Professional Aim is: (Services then Solutions then Satisfactions) I hope you are good. As an experience in this field from last 5 years i am sure i can do it perfectly with in a time and budget Able to deliver Thêm

$20 USD / giờ
(65 Nhận xét)
5.9
etalhak

Hello, I am an electronics and telecommunication engineer and my major is wireless systems' design. I am experienced in hardware and embedded systems' design. I have designed/printed/tested many PCBs and I am quite exp Thêm

$20 USD / giờ
(45 Nhận xét)
5.5
mahmoudralizadeh

Hi I almost understood what you want just a few details What should be the frequency range of radar? Is it pulse doppler or cw radar? I am a communication engineer with knowledge in radar systems Also expert in micro Thêm

$25 USD / giờ
(8 Nhận xét)
3.8
ducchunguyen

Hello I have an exercise before doing the counting the bicycle using radar sensor from Ti. It's may look the same as your requirement. The chip we're using Is IWR1642. For the FCC standard, we're a must-be design matc Thêm

$15 USD / giờ
(1 Nhận xét)
2.0