Đã hoàn thành

Small Assignment of Infrared Music Transmission System

This assignment is based on student budget.

The circuits are consist of Transmitter and Receiver, those two circuits are transmitted by Infrared LED (Tx & Rx).

It would be a simulation of the circuits, and the components hardware in the breadboard.


Mono or Stereo jack is connected from the transmitter, and we must have a tuner (variable resistor in transmitter) to tuning the volume, then we can hear the sound from the transmitter respectively.

The Objectives:

*Able to hear the sound at the transmitter as well as the input music (with any modulation technique, AM is preferable)

*Adjust the tuner, as to be the volume control of the sound


We can use any types of components. Simple basic Amplifier is recommended.

No need Programmable IC or microcontroller Unit. Just use an IC or OP-AMP chips.

The components that available at the moment right now,

*Transistor NPN BC548 and PNP 558,

*Mono Speaker 8 Ohms,

*UM66 and LM 386 for music,

*OP-AMP 741,

*Diode Zener 3.2 V,

*3 pairs of LEDs Transmitter and Receiver,

*Male jack [url removed, login to view] (due to connection cable from computer to hardware),

*Female stereo and mono for jack [url removed, login to view] cable,

*Voltage regulator,

*Some Capacitors and Resistors,

*Battery 9V 2pcs,

*Variable Resistors 10k Ohm, 100k Ohm


[url removed, login to view]

[url removed, login to view]

[url removed, login to view]

Budget is not more than $40. And the complete period would be just 3 days, from the day it posted.

Submission Maximum at Monday April 4th.

Description of Works:

1) Simulation of schematic the current circuits for both transmitter and receiver, by using Multisim or Proteus.

This simulation may be successful in the process, but it must applied to the actual components until the project works.

2) Full explanations of the simulation part. (Ms. Word files and component datasheets)

For instance;

* What modulation technique do we use.

* Basic calculations or any equations that require in the simulations

* Why we use this type of amplifiers? (i.e. OP-AMP 741)

* What the purposes of these resistor of ... Ohm, Capacitor or any IC in the circuit,

* If the transmitter use modulation, how the demodulation signal going through at receiver,

* If the sound it is not clear as the input, what happened to the signals?

* Why it come with noise at the receiver?

* And other explanations, regarding how the circuit works properly.

NOTE : The job is only the schematic simulations in the software ($25) and full explanations of why it works and operates, I would ask some questions if necessary ($15). Therefore I will construct the hardware in the breadboard myself.

Kĩ năng: Kĩ thuật điện, Điện tử, Kĩ thuật, Toán học, Viết báo cáo

Xem nhiều hơn: music transmission infrared, www electronics engineering com, www electronics and communication engineering com, what is computer illustration, voice tuner, speaker simulation software, speaker simulation, proteus engineering, op note, need an engineering student, microcontroller job, job objectives, illustration forum, engineering job description, doc note, be electronics engineering, basic electronics engineering, atp files, at and t wireless, any type of job, 123 voice, music transmission, amp transmitter receiver circuit multisim, um66 proteus, small microcontroller

Về Bên Thuê:
( 4 nhận xét ) Kuala Lumpur, Malaysia

ID dự án: #1008159

Được trao cho:


Hi, Please check PM

$40 USD trong 2 ngày
(2 Đánh Giá)

4 freelancer đang chào giá trung bình $40 cho công việc này


I am very much interested in your work. Please check my PM.

$40 USD trong 3 ngày
(14 Nhận xét)

Hi, I am an electronics engineer by background with 3 yrs of work [login to view URL] worked on a lot of electronics projects. Please read PM. Regards, Rakesh Bisht

$40 USD trong 2 ngày
(0 Nhận xét)

it will be very simple .i am working on proteus for more than 4 years. so if u wana intrested i willdo this do in the aove mentioned days

$38 USD trong 2 ngày
(0 Nhận xét)