Đã Đóng

0-24 VDC power supply board design

This project consists of providing a board design and component list for a circuit board which will provide variable DC power to a device. Part numbers of components must be specified for:

1. A connector which mounts to the board which mates to the 24 volt 1 amp power supply specified by Digikey part number T1073-P5P-ND. Please specify a part which is in stock at one of the major electronics retailers such as digikey, mouser, allied or newark

2. A potentiometer with a thumb wheel in the range of 10-15 mm in diameter which is large enough and mechanically robust enough to act as the main control for the power. Again, select a part which is in stock at a major retailer and give part number. The selection of value is up to the designer. The thumb wheel should be in the plane of the board, so that the axis of rotation is perpendicular to the board. The location of the pot should be on the edge of the board so that it can stick out the side of the final artifact and act as a user power control.

3. Whatever other components, presumably a regulator and capacitors, which are required to regulate voltage from 0 V up to the maximum of 24 V available from the supply, with up to the full 1 A of current.

4. If the potentiometer can have a position at one end of rotation where it "clicks" into an off state that is ideal, but if that is not possible, also specify a switch which can stick off the edge of the board for on/off switching. I envision this as a latching rocker switch which is off the opposite side of the board as the pot.

Completion of the project will include generally readable board files which are suitable for submission to a board fabrication house as well as part numbers for the above components. Suggestions for improvement are welcome if you see a way to improve some aspect of this project. File format for circuit board should ideally be compatible with Eagle circuit board design software.

Circuit board should ideally be 24 mm by 24 to 40 mm, the smaller the better, but this is flexible. Corners should have clearance holes for #4 screws far enough in from the corners to be mechanically robust. Output should be a pair of plated holes which can be soldered to.

Thank you.

Kỹ năng: Kĩ thuật điện, Điện tử, Kĩ thuật

Xem thêm: t1073 p5p, vdc power supply design, power circuit board, board power supply design, variable power supply vdc, design vdc power supply, volt amp power supply, power supply vdc, power supply board design, wheel well, the design pot, supply one, software design components, software component design, robust design, power up 2, power part 2, opposite of maximum, number board design, newark electronics, mouser electronics, in design software, engineering design software, designer electronics, dc design house

Về Bên Thuê:
( 0 nhận xét ) Nepal

Mã Dự Án: #1064048

9 freelancer đang chào giá trung bình $233 cho công việc này

reallifetech

See details in MB.

$400 USD trong 14 ngày
(17 Đánh Giá)
4.5
RightAndAbove

please see pm

$250 USD trong 7 ngày
(1 Đánh Giá)
2.2
tauseefmalik

hie electronics guru here! lets start the work ! pmd u the details

$250 USD trong 7 ngày
(0 Đánh Giá)
0.0
bkalaska

Am a retired electrical engineer. Have built many of these. For my bid price I will supply everything you are asking for plus a working prototype.

$250 USD trong 20 ngày
(0 Đánh Giá)
0.0
Vahejan

already have done the project with LM2***** DC-DC converter. But have a limitation on low voltage that begins from [url removed, login to view]

$65 USD trong 1 ngày
(0 Đánh Giá)
0.0
piezoengineer

please see PMB

$180 USD trong 2 ngày
(0 Đánh Giá)
0.0
Kung

Dear patiram425, Please see my PM for the details of my bid. Regards Gergely

$250 USD trong 7 ngày
(0 Đánh Giá)
0.0
daraj

i can do this job

$200 USD trong 4 ngày
(0 Đánh Giá)
0.0
Roneol

I am experienced in PCB design on Eagle. This is quite simple design. Here is my Quote: 6 hours PCB Design 2 Hours Quality review 2 Hours Customer in-Design Feedbacks and corrections. Feel Free to contact me fo Thêm

$250 USD trong 7 ngày
(0 Đánh Giá)
0.0