Đã Đóng


Overview ( See Full details, in attached file)

A new coal mine and an associated township are proposed to be built in the area near the Golden River

in Tasmania. Torrensville City Council (the Client) has engaged your firm to provide a conceptual

design for a reservoir system for the proposed mining site and nearby township. The reservoir will be

located in the valley of the Golden River to collect water from the upstream catchment and serve as the

water source for the proposed mine site and the township. You are required to carry out the following

modelling and design tasks.

Task 1. Embarkment Dam (25 marks)

An embankment dam is proposed to be built to manage the water flow from the water storage reservoir

to downstream. Geotechnical site investigations have been conducted. Nine boreholes (BH1~9) were

drilled across the valley with the plane layout as shown in Fig. 1.1. Each borehole is 35 m deep from

the ground soil surface. Core samples were collected from the nine boreholes and tested in a soil

laboratory. As illustrated in Fig. 1.2, five layers of different soils were identified from visual observation

and laboratory tests, which are labelled as L1, L2, L3, L4 and L5. Note that L5 is the bedrock. A lens

of L2 can be observed at BH7, where the extent can be assumed as 2.5 m from the centre of the borehole.

1.2 According to the Client requirement, the seepage through the dam (including through the underlying

soil) must be less than 0.85 m3

/day per metre length of the dam. The Client approved the adoption of

SEEP/W as analysis software in calculating seepage rate. The water depth in the reservoir during wet

season is equal to 10m.

The width of the dam top is 5m and dam shell slope is 2:1. The dam height and the material of the dam

should be determined by you in this conceptual design phase (Fig. 1.4). When determine the overall

height of the dam, an extra 5% of the height should be left to accommodate long term settlement. In

addition, a minimum freeboard should be 0.50 m and an additional 0.25m should be taken into account

if there is potential wave action.

The parameters of material and associated cost of the dam are listed in Table 1.2, which is to assist your

design and assess your design budget.

(1) Please assess the seepage and flow rate through the dam as shown Fig.1.4. In your report, the

flow net contours and seepage velocity contours through the dam should be shown and

maximum seepage velocity should be estimated. Also, provide the evidence of your model

setup of boundary condition and explain the reasons of your definition. (5 marks)

(2) To reduce potential hazard at the flow exit, two preliminary design options by using blanket

drain and toe drain are provided in Fig. 1.5 and Fig. 1.6. Please estimate the seepage rates and

show how the drain design options influence the flow net contours through the dam. Also show

the seepage velocity contours and estimate the maximum seepage velocity. Compare the results

with those of (1) and discuss the functionality of the drain system based on the comparison. (4


(3) You are required to select one of the drain options that have been discussed in (2). If your

calculated seepage did not meet the requirement, propose your design to reduce seepage. The

properties of core material that can be considered are provided in Table 1.2. For constructability

purpose, only one type of core material is recommended to be used in this design. You are

recommended to find available industry design guidelines and other reliable references to

support your design process. (9 marks)

(4) Compare the shape of phreatic line from all your analysis scenarios and explain what are the

reasons of the difference. Based on your final recommendation in (3), describe the changes of

phreatic line when it goes through different materials and explain this phenomenon by using

the knowledge you learned. (3 marks)

Kĩ năng: Địa chất, Kĩ thuật dân dụng, Địa chất công trình

Xem nhiều hơn: emoticons full details, full details array programming, want full details car formate, taj incident full details, project full details php, full details indian mobile numbers, 3d model ship full details, asp net project full details, exchange receive send connector full details, freelancers android projects full details, full details dotnet networking project, full details indian mobile phone, full details marketing websites, illustrator web full details, java full details, work swish max version full details, seo full details, full details, please refer attached file details

Về Bên Thuê:
( 654 nhận xét ) Bangalore, India

ID dự án: #31832754

1 freelancer đang chào giá trung bình ₹11000 cho công việc này


Hi! I’m Guru and I have read the project description and attached file thoroughly. I have done my masters in water resources from one of the top institutions of India. Me and my friend Ashish will be handling this pr Thêm

₹11000 INR trong 10 ngày
(1 Nhận xét)