Đã hoàn thành

PI CM3+ Compute Module Schematic and PC Design

Job Description:

Create Circuit Boards for Raspberry PI Compute Module 3

Breakout Board for Raspberry Pi CM3+

2X USB A Ports

1X DSI Input for Display

4X buttons (to trigger GPIO )

1X Ethernet Port

2X CAN BUS (1 MBIT with MCP2515 based on PICAN DUO Layout) 120 ohm End resistors should be broken out to the main connector to be able to enable / disable via loop on main connector

8X Analog 0-5 V inputs (with overvoltage protection )

8x Digital 5 - 14 V inputs (overvoltage protection optocupler ?)

1X LDR Sensor (To be able to automatically dimm the display)

1X Real Time Clock incl button battery

1x Speaker

1x Voltage Converter with Shutdown Circuit (10-15 V input ) Stepdown to 5,1V and 3,3 V .(Voltage loss should trigger a GPIO pin so I can switch off the Pi safely by monitoring the PIN )

 Switched 12 V input should trigger the Circuit to switch on the CM . There should be a Capacitor which can supply enough power to the PI CM for 20 Seconds in order to trigger a safe shutdown via GPIO Pin , as well as stabilize the Power during cranking of the CAR .

1x WIFI with external Antenna Connection

There should be 1 34 Way Connector (Amp Superseal 2-6447232-3) for the following connections

1x Sensor Ground 9 Ground for the Analog inputs

8x Analog inputs

2x CAN High

2x CAN Low

8 x Digital inputs

1x 10-14 V Input

1x Main Ground

1x 3,3 V out

1x Ground out

1X SDA out

1X SDL out

2x Bridgeable pins for CAN 1 120 Ohm resistor

2x Bridgeable pins for CAN 2 120 Ohm resistor

Separate PCB’s ( To plug and play for modularity )

1x GPS Ublox Neo M8N via Serial with external Antenna Connection

6x Adressable RGB led on separate PCB mounted in one row

Kĩ năng: PCB Design and Layout, Thiết kế vi mạch, Raspberry Pi

Về khách hàng:
( 9 nhận xét ) Pretoria, Germany

ID dự án: #26946508

Được trao cho:


Greetings!! I read the overview of your project and am interested in working with you. I am an ELECTRICAL/ELECTRONICS ENGINEER from India with 4+ years of experience in designing circuits and PCBs. With my precision an Thêm

$250 USD trong 3 ngày
(28 Đánh Giá)

6 freelancer chào giá trung bình$272 cho công việc này


Hi I am experienced electronics engineer with more than 15 years of experience in PCB design. I have read the details and have a few questions. Please get in touch to discuss it further Regards

$750 USD trong 7 ngày
(49 Nhận xét)

Best PCB Design Expert at your doorstep! Dear Client, I couldn’t stop myself from bidding after going through the description as they are an exact match with my skillset and experience. I have experience in PI CM3 Co Thêm

$180 USD trong 2 ngày
(21 Nhận xét)

Dear Client, I have read and understood your requirements and could do it for you in the least time and utmost superior quality. I have experience in PI CM3 Compute Module Schematic and PC Design and could design it fo Thêm

$180 USD trong 2 ngày
(2 Nhận xét)

Hi dear I am an electronics engineer and I have industrial experience of power electronics circuit and PCB layout designing. I did read your project description and can design a PCB layout up to 16 layers. Share your p Thêm

$130 USD trong 7 ngày
(15 Nhận xét)