Find Jobs
Hire Freelancers

Design a PCB for a Vending Machine Matrix Motor Driver

$30-250 USD

Đã hoàn thành
Đã đăng vào hơn 4 năm trước

$30-250 USD

Thanh toán khi bàn giao
We are looking to drive a matrix of 24V DC Motors by i2c. (7 by 10 Matrix) This is to replace an old vending machine motherboard and to have it interface with an Arduino controller by i2c. We can provide detailed pictures of the motherboard made in 1984; It uses the following parts to drive the motors: MJE700 (60V / 4A) ULN2064B (50V / 1.5A) The motor detects a full rotation by shorting the motor briefly; I assume the motherboard detects the current drop and stops powering the motor until the next vend command. We would like to control vends by i2c from another micro controller. The matrix of motors is fully mapped out. The finished PCB should take mains 120v AC in and power the 24 volt motors using fault tolerant parts (ie; handling high current motor draw and feed back, exceeds max values on parts) unidirectionally. and controlled by an i2c input.
Mã dự án: 22784411

Về dự án

2 đề xuất
Dự án từ xa
Hoạt động 4 năm trước

Bạn muốn kiếm tiền?

Lợi ích khi chào giá trên Freelancer

Thiết lập ngân sách và thời gian
Nhận thanh toán cho công việc
Phác thảo đề xuất của bạn
Miễn phí đăng ký và cháo giá cho công việc
Đã trao cho:
Avatar người dùng
Hello, I'am experienced in, Digital / Analog Electronics ESP32 , ESP8266 , Arduino, PIC , AVR , ARM , STM32 , 8051 Programming Single board computers ( Raspbery pi,Orange pi etc) C , C++ , Java , Python , C# PCB designing (Altium designer,Kicad,Eagle etc) Embedded System IoT WiFi , UART , I2C , SPI , BLE , BT , GSM , GPRS ,GPS , RF Amazon Web Services / Microsoft Azure Linux Android Development,Web Development please leave a message on my chat so we can discuss. Best, Malindu
$70 USD trong 6 ngày
3,8 (10 nhận xét)
3,7
3,7
2 freelancer chào giá trung bình $118 USD cho công việc này
Avatar người dùng
Hi, So just give me opportunity to show you what I have done until now and that would be enough recommendation for me, because I'm the new one here and it's really hard to find a job as a beginner on this. Also I'm working with Altium, and dont know, is that okay! Regards, Emir
$166 USD trong 4 ngày
5,0 (1 nhận xét)
1,6
1,6

Về khách hàng

Cờ của UNITED STATES
Hammond, United States
5,0
24
Phương thức thanh toán đã xác thực
Thành viên từ thg 5 8, 2017

Xác thực khách hàng

Cảm ơn bạn! Chúng tôi đã gửi email chứa đường link để bạn lấy tín dụng miễn phí.
Đã xảy ra lỗi trong khi gửi email của bạn. Hãy thử lại.
Người Dùng Đã Đăng Ký Tổng Số Việc Đã Đăng
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Đang tải xem trước
Đã cấp quyền truy cập vị trí.
Phiên đăng nhập của bạn đã hết hạn và bạn đã bị đăng xuất. Hãy đăng nhập lại.