ESP32 custom PCB design for manufacture

Đã Đóng Đã đăng vào 4 năm trước Thanh toán khi bàn giao
Đã Đóng Thanh toán khi bàn giao

I have developed a prototype device using an ESP32 dev board and a few components connected to GPIO pins (micro SD card breakout, mono I2S amplifier, rotary encoder) and would like a custom PCB designed to build all of this onto one board.

The PCB should allow easy flashing of the ESP32 module over micro-USB with EN and BOOT buttons.

Ideally this should be designed in a way that can be ordered from manufacturers in China (or elsewhere) fully assembled with components soldered. Or alternative suggestions for easy assembly are welcome.

PCB design files should be provided in EasyEDA or KiCAD formats.

Thanks!

Sarab

PCB Layout Điện tử Vi điều khiển Thiết kế vi mạch DFM (Design for Manufacturing)

ID dự án: #21580491

Về dự án

21 đề xuất Dự án từ xa 4 năm trước đang mở

21 freelancer chào giá trung bình£206 cho công việc này

sagradoamicus

Hi I am experienced PCB designer with more than 11 years of experience. I can do it for you. I have worked on a number of projects before. Please share the further details of the project. I am waiting for your reply t Thêm

£250 GBP trong 7 ngày
(251 Nhận xét)
8.0
trailblazer42

Hello there, I have read your project description and I could do that for you. I usually work in KiCad which is open source and I send the project files too. I will provide you with all manufacturing files you need for Thêm

£160 GBP trong 5 ngày
(63 Nhận xét)
6.7
bijan01in

Hi I am interested to your project. I am familiar with electronics, microcontroller as well as PCB design by Eagle. Thanks.

£225 GBP trong 7 ngày
(99 Nhận xét)
6.4
microembedded

HI there I an an electrical engineer with 8+ years of experience with PCB designing. I can design this project for you and can provide you manufacture able files. Let me know if you are interested

£350 GBP trong 7 ngày
(30 Nhận xét)
6.4
mmicronta

Hi, Sounds like it is not a complex job. I wager two-layer board will be sufficient, just complete a fairly similar ESP32 job. I know Altium very well. I am also an Electrical Engineer and PCB designer in my daytime Thêm

£250 GBP trong 7 ngày
(30 Nhận xét)
5.8
MarcoCiau

Hello Sir, I'm interested in the position of PCB & Schematic Design you recently posted, particularly being of Hardware Engineering. I have experience in PCB design using KiCad, hands-on knowledge on schematic ca Thêm

£166 GBP trong 15 ngày
(17 Nhận xét)
6.0
tokumei

Hi Sarab, Good day! This is Lawrence and I would like to design your custom board. Please feel free to contact me anytime to discuss more about your requirement. I'll be available to start anytime. Thank you, Lawren Thêm

£100 GBP trong 14 ngày
(8 Nhận xét)
4.8
noumanalishakir

Hello, I am Electrical Engineer and interested in your project. I have some questions regarding your project. Please tell me about your time limits? When you want your project to be completed? See my profile and review Thêm

£333 GBP trong 10 ngày
(14 Nhận xét)
4.4
sourabh470

Hello Sir, I have 4 years experience in PCB designing in EAGLE( single multilayer and flex). following are some examples of my work 1. ESP12E wifi + relay board + humidity&temp sensor Smart module 2. ESP12S wifi + r Thêm

£135 GBP trong 7 ngày
(16 Nhận xét)
4.0
ranjukravi

i am using KiCad for PCB designing so i will able to design your board ,so please give me more details like your required dimension...

£100 GBP trong 7 ngày
(9 Nhận xét)
4.1
Muratzz

Hello, I will build would like a custom PCB designed to build all of this onto one board as u want. Of course, I will design in a way that can be ordered from manufacturers in China. If you want, we can discuss in det Thêm

£200 GBP trong 5 ngày
(4 Nhận xét)
3.0
george19921014

Hello! Nice to meet you! I have read your project fully. I am very interested in your project. I am a Microelectronics engineering expert. I have a lot of experience on ARM, FPGA, DSP, Arduino, Raspberry, PIC, ATMega a Thêm

£200 GBP trong 7 ngày
(2 Nhận xét)
3.0
stenniswood

I would be happy to do so, however I only use Eagle CAD software. The end output of Gerber files will be the same however.

£150 GBP trong 7 ngày
(1 Nhận xét)
2.4
ManingM

Hi. I have more than five years of experience in designing and development. I can customize esp32 dev board according to your requirements. I also have pcba manufacturing facilities based in China. I can design and man Thêm

£222 GBP trong 10 ngày
(1 Nhận xét)
2.2
elecjuncled

Dear Sir, We are from India, We can give you end to end service means we can design schematic from your hand drawn circuit and then put into layout and after layout we can get it manufacture good quality PCB. we are de Thêm

£200 GBP trong 15 ngày
(0 Nhận xét)
0.0
MilanYadav7

I have already developed Esp32 custom PCB for many vendors so you will not face any issues from my side. Relevant Skills and Experience I can give you your design in 4 working days in preferred format

£111 GBP trong 5 ngày
(0 Nhận xét)
0.0
munshisohel1144

Hi, I have been working with schematic as well as PCB design from last 7 years and can help you out with your application. I am a full time freelancer looking for a long term partnership. I respect your intellectual p Thêm

£222 GBP trong 10 ngày
(0 Nhận xét)
0.0
navid11900

I can easily design PCB layout based on your circuits and even promote them for decreasing the PCB layout size.

£250 GBP trong 14 ngày
(0 Nhận xét)
0.0