Find Jobs
Hire Freelancers

3.5in Touch TFT LCD Arduino Shield with WeMOS D1 R32 Board (ESP32)

$15-25 USD / hour

Đã hoàn thành
Đã đăng vào khoảng 3 năm trước

$15-25 USD / hour

My company is planning to develop a new industiial hardware device. To do that, we're planning to test various MCU platforms and Touchscreens. We need help of a freelancer who have experiences with wide range of MCUs and Displays Till now, my company used TI and Nordic chips for our IoT projects. Now we're going to move to other more popular MCUs, because we were unable to find a good freelancers on TI and Nordic platforms. For the proof of concepts, the awarded freelancer only needs to display * simple b/w text "Hello World" * Colored text 123456789") in different colors Here're each desired pairs of MCU + Display 1. WeMOS D1 R32 (ESP32) + 3.5in TFT Touch LCD Arduino Shield (ILI9841, Parallel) 2. Raspberry Pico + 3.5in TFT Touch LCD Arduino Shield (ILI9841, Parallel) 3. Raspberry Pico + 2.8in TFT Touch LCD Module (ILI9841, SPI) 4. STM32L476RG + 3.5in TFT Touch LCD Arduino Shield (ILI9841, Parallel) We believe that each pair testing is less than 3 hours of work for an experienced developer. Thus, for each pair implementation, budget is $40. We'll create each #40 milestone for each pair, and will provide remote computer access with all the hardwares connected. After one of the PoC approved, the product development will be started in a bigger scale. Please do not bid if you're going to raise budget after bidding. Thanks, Bhavya Sai. System Engineer at Easter Electronics Inc. (Sydney, Australia)
Mã dự án: 30144670

Về dự án

3 đề xuất
Dự án từ xa
Hoạt động 3 năm trước

Bạn muốn kiếm tiền?

Lợi ích khi chào giá trên Freelancer

Thiết lập ngân sách và thời gian
Nhận thanh toán cho công việc
Phác thảo đề xuất của bạn
Miễn phí đăng ký và cháo giá cho công việc
Đã trao cho:
Avatar người dùng
Hello, thank you for your job posting. I read your description about your project I am a senior electrical engineer. I have plenty of experience in firmware development and micro-controller developments. I can write the firmware based on Arduino, Raspberry Pi, Pic, Atmega, FPGA, ARM, DSP, PLC and so on. And I can design the circuit by the Altium, Eagle, KiCAD, Allegro & OrCAD, PADs. I provide the services - Gerber files, Netlist generation, BOM generation and 3D Models of PCAD and ECAD. I am also good at AutoCAD, Solidworks. And I can simulate all circuits with Proteus, LT-spice, Matlab, Simulink, Multisim, and Labview as well. Due to my experience in firmware development, I will bring you the perfect result in time with high quality. I will also give you a detailed explanation of the process. Looking forward to hearing from you soon Thanks
$20 USD trong 40 ngày
5,0 (19 nhận xét)
5,4
5,4
3 freelancer chào giá trung bình $20 USD/giờ cho công việc này
Avatar người dùng
I will start with STM32, as I am already openning CubeIDE, every day I will send you a pair test, it will took 4 days in total
$15 USD trong 40 ngày
5,0 (4 nhận xét)
3,5
3,5

Về khách hàng

Cờ của UNITED STATES
roundrock, United States
0,0
0
Phương thức thanh toán đã xác thực
Thành viên từ thg 2 25, 2021

Xác thực khách hàng

Cảm ơn bạn! Chúng tôi đã gửi email chứa đường link để bạn lấy tín dụng miễn phí.
Đã xảy ra lỗi trong khi gửi email của bạn. Hãy thử lại.
Người Dùng Đã Đăng Ký Tổng Số Việc Đã Đăng
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Đang tải xem trước
Đã cấp quyền truy cập vị trí.
Phiên đăng nhập của bạn đã hết hạn và bạn đã bị đăng xuất. Hãy đăng nhập lại.