Design LTE hardware from Base band Unit, EnodeB and Transmitters

min $5000 USD

Đã đóng

Đã đăng vào

gần 11 năm trước

min $5000 USD

Thanh toán khi bàn giao

We are looking at producing a 10W LTE to meat the requirements of release 11. consideration for release 12- 15 should be provided. design with an integrated EnodeB and BBU design objectives - 1) small footprint 25cx X 25cm to fit inside a pole - reasonable vertical height available for design 2) reliability under extreme conditions - high heat, limited air flow, high humidity etc. 3) LTE EnodeB and BBU unit should be of same footprint and possible Plugged together? top to bottom. 4) TDD capability a primary priority (frequency / band coverage should be "Chip" dependant ie base unit supports any frequency chip installed. 5) 40Mhz, in 20Mhz blocks (ideally 60Mhz perhaps as a field implemented optional upgrade?) 6) option for a FDD EnodeB to connect to same BBU - ie support both TDD and FDD from same transmitter location. 7) as low power consumption as possible.(note no room for any equipment at base of Pole ? 8) Transmitter areal plugged external either Omni- areal or Directional, high gain 9) transmitters should be designed for maximum gain at 10w or 15w of power - knowledge of DB output etc required. 10) Drawings and IP will be transferred to purchaser (me). 11) Time to design a issue? estimate should be provided. we are planning to manufacture units and want to "Buy" the working design. We are not available for a per unit Royalty will also consider bidders who bid on certain parts ie EnodeB, BBU or transmitters separately

Electrical Engineering

Electronics

Microcontroller

PCB Layout

Telecommunications Engineering

Mã dự án: 4726977

Về dự án

6 đề xuất

Dự án từ xa

Hoạt động 11 năm trước

Bạn muốn kiếm tiền?

Địa chỉ email

Lợi ích khi chào giá trên Freelancer

Thiết lập ngân sách và thời gian

Nhận thanh toán cho công việc

Phác thảo đề xuất của bạn

Miễn phí đăng ký và cháo giá cho công việc

6 freelancer chào giá trung bình $440.910 USD cho công việc này

@MikroStar

hi, i am an electrical engineer and an embedded system designer. i can help you with this project.

$515.463 USD trong 250 ngày

4,8

(54 nhận xét)

6,7

@betaenergy

Dear Sir, I'm 15 year experienced Electronics Engineer whose working area is directly related to your project. I have designed several system which is related to your project. I have high level experience about hardware design, analog design, embedded system, microcontroller, power electronics, system simulation, digital motor control. Examples related to your project are attached. It shows my ability to make your project. If you investigate example, you will see that I have strong background similar to your projects. Project lists which I have made until now is attached also. We can determine budget by discussing details of your project. I’m open to work with amount which you can pay. Any questions, you can ask me. The way which will be used to implement is such as: - My profile is below. It shows every issues related to your project. Please evaluate it carefully. If you do it, you will see that I'm ideal candidate who can make your project without any problem. I will wait for being started contract. Regards. Metin Dear Sir, We are Reserach and Development company whose working area are : -Digital Motor Control -Analog Design -Electronic Design -Power Electronics -PCB design -Embedded system -Matlab -Simulation of hardware For each concept descriptions are as follows: Digital Motor Control: -3-phase induction motor vector control drive -Flux estimation algoritm generation -DSP(TMS320) implementation on motor drive -Low speed application -Torque and speed loop generation -Control algoritms Analog design -Low power distribution -Noissless special opamp based analog circuits -Analog filters -Orcad simulation of several circuits Electronic Design -RF transmitter and receiver -Bluetooh reader and transmitter -Magnetic reader Power Electronics -Implementation motor drive -AC/DC converter -DC-DC converter -Battery charger -Solar inverter -Renewable Energy simulations -Uninterruptle power supplies PCB design -Schematic design by Altium -PCB design by Altium -Power board design -SMPS board design Embedded system -PIC18,PIC24,PIC30 and dsPIC applications -Ardino -MSP430 -Atmel -DSP(Texas Instruments) -Renesas Matlab -Power Electronics simulation -Motor drive -Wind Energy -Solar Energy -Control applications Simulation of Hardware -Orcad Simulation(TI,National, Linear Tech, Maxim libraries) -LTI -National -Matlab Very important Note: References attached. Please look excel file to see projects which we made until now! Metin

$5.555 USD trong 3 ngày